667030
12
Zoom out
Zoom in
Previous page
1/50
Next page
10
>> www.celestron.com
Don’t worry about confusing planets for stars when selecting
alignment objects. SkyAlign works with the four brightest planets
(Venus, Jupiter, Saturn and Mars) as well as the Moon. In addition
to the planets, the hand control has over 80 bright alignment stars
to choose from (down to 2.5 magnitude).
Rarely SkyAlign will not be able to determine what three alignment
objects were centered. This sometimes happens when a bright
planet or the Moon passes near one of the brighter stars. In situations
like these, it is best to try to avoid aligning to either object if possible.
For the best possible pointing accuracy, always center the
alignment stars using the same nal movements as the direction of
the GoTo Approach (by default this will be using the up arrow button
and the right arrow button). Approaching the star from this
direction when looking through the eyepiece will eliminate much
of the backlash between the gears and assure the most accurate
alignment possible.
Auto Two-Star Align
As with SkyAlign, Auto Two-Star Align downloads all the necessary time/
site information from orbiting GPS satellites. Once this information is
received, the CPC will prompt you to slew the telescope and point at
one known star in the sky. The CPC now has all the information it needs
to automatically choose a second star that will assure the best possible
alignment. Once selected, the telescope will automatically slew to the
second alignment star to complete the alignment. With the CPC set up
outside with all accessories attached and the tripod leveled, follow the
steps below to align the telescope:
1. Once the CPC is powered on, Press ENTER to begin alignment.
2. Use the Up and Down scroll keys (10) to select Auto Two-Star Align
and press ENTER.
3. The hand control will display the last time and location information
that was entered or downloaded from the GPS. Use the Up and
Down buttons to scroll through the information. Press ENTER to
accept the downloaded information or press UNDO to manually
edit the information.
4. The display will now prompt you to select a bright star from the
displayed list on the hand control. Use Up and Down buttons (6 and 9
on the keypad) to scroll to the desired star and then press ENTER.
5. Use the arrow buttons to slew the telescope to the star you selected.
Center the star in the crosshairs of the nderscope and press ENTER.
Finally, center the star in the eyepiece and press ALIGN.
6. Based on this information, the CPC will automatically display the most
suitable second alignment star that is above the horizon. Press ENTER
to automatically slew the telescope to the displayed star. If for some
reason you do not wish to select this star (perhaps it is behind a tree
or building), you can either:
Press the UNDO button to display the next most suitable star
for alignment.
Use the UP and DOWN scroll buttons to manually select any star
you wish from the entire list of available stars.
Once the desired star is displayed, press ENTER to automatically slew
the telescope to the displayed star. When nished slewing, the display
will ask you to use the arrow buttons to align the selected star with the
cross hairs in the center of the nderscope. Once centered in the nder,
press ENTER. The display will then instruct you to center the star in the
eld of view of the eyepiece. When the star is centered, press ALIGN to
accept this star as your second alignment star. When the telescope has
been aligned to both stars the display will read Alignment Success, and
you are now ready to nd your rst object.
Two-Star Alignment
With the two-star alignment method, the CPC requires the user to know
the positions of two bright stars in order to accurately align the telescope
with the sky and begin nding objects. Here is an overview of the two-
star alignment procedure:
1. Once the CPC is powered on, use the UP and DOWN scroll keys (10) to
select Two-Star Align, and press ENTER.
2. Press ENTER to accept the time/site information displayed on the
display, or wait until the telescope has downloaded the information
from the GPS satellites.
3. The SELECT STAR 1 message will appear in the top row of the display.
Use the UP and DOWN scroll keys (10) to select the star you wish to
use for the rst alignment star. Press ENTER.
4. CPC then asks you to center in the eyepiece the alignment star you
selected. Use the direction arrow buttons to slew the telescope to the
alignment star and carefully center the star in the nderscope. Press
ENTER when centered.
5. Then, center the star in the eyepiece and press ALIGN
In order to accurately center the alignment star in the eyepiece,
you may wish to decrease the slew rate of the motors for ne
centering. This is done by pressing the RATE key (11) on the hand
controller then selecting the number that corresponds to the
speed you desire. (9 = fastest, 1 = slowest).
6. CPC will then ask you to select and center a second alignment star
and press the ALIGN key. It is best to choose alignment stars that are
a good distance away from one another. Stars that are at least 40º to
60º apart from each other will give you a more accurate alignment
than stars that are close to each other.
Once the second star alignment is completed properly, the display will
read Alignment Successful, and you should hear the tracking motors
turn-on and begin to track.
One-Star Align
One-Star Align allows you to download all the same information as you
would for the Two-Star Align procedure. However, instead of slewing to
two alignment stars for centering and alignment, the CPC uses only one
star to model the sky based on the information given. This will allow you
to roughly slew to the coordinates of bright objects like the Moon and
planets and gives the CPC the information needed to track objects in
altazimuth in any part of the sky.
To use One-Star Align:
1. Select One-Star Align from the alignment options.
2. Press ENTER to accept the time/site information displayed on the
display, or wait until the telescope has downloaded the information
from the GPS satellites.
3. The SELECT STAR 1 message will appear in the top row of the display.
Use the Up and Down scroll keys (10) to select the star you wish to use
for the rst alignment star. Press ENTER.
4. The CPC then asks you to center in the eyepiece the alignment star
you selected. Use the direction arrow buttons to slew the telescope
to the alignment star and carefully center the star in the nderscope.
Press ENTER when centered.
5. Then, center the star in the eyepiece and press ALIGN
6. Once in position, the CPC will model the sky based on this information
and display Alignment Successful.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CPC Deluxe 800 HD - 11007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CPC Deluxe 800 HD - 11007 in the language / languages: English as an attachment in your email.

The manual is 10,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info