Manual Celestron CGE Pro 1400 (page 51 of 72) (English)

667042

Zoom out

Zoom in

1/72

The three collimation screws are located

on the front of the secondary mirror

housing.

While your telescope requires little maintenance, there are a few things to remember that will ensure your telescope

performs at its best.

Care and Cleaning of the Optics

Occasionally, dust and/or moisture may build up on the corrector plate of your telescope. Special care should be

taken when cleaning any instrument so as not to damage the optics.

If dust has built up on the corrector plate, remove it with a brush (made of camel’s hair) or a can of pressurized air.

Spray at an angle to the lens for approximately two to four seconds. Then, use an optical cleaning solution and

white tissue paper to remove any remaining debris. Apply the solution to the tissue and then apply the tissue paper

to the lens. Low pressure strokes should go from the center of the corrector to the outer portion.

Do NOT rub in

circles!

You can use a commercially made lens cleaner or mix your own. A good cleaning solution is isopropyl alcohol

mixed with distilled water. The solution should be 60% isopropyl alcohol and 40% distilled water. Or, liquid dish

soap diluted with water (a couple of drops per one quart of water) can be used.

Occasionally, you may experience dew build-up on the corrector plate of your telescope during an observing

session. If you want to continue observing, the dew must be removed, either with a hair dryer (on low setting) or by

pointing the telescope at the ground until the dew has evaporated.

If moisture condenses on the inside of the corrector, remove the accessories from the rear cell of the telescope.

Place the telescope in a dust-free environment and point it down. This will remove the moisture from the telescope

tube.

To minimize the need to clean your telescope, replace all lens covers once you have finished using it. Since the rear

cell is NOT sealed, the cover should be placed over the opening when not in use. This will prevent contaminants

from entering the optical tube.

Internal adjustments and cleaning should be done only by the Celestron repair department. If your telescope is in

need of internal cleaning, please call the factory for a return authorization number and price quote.

Collimation

The optical performance of your telescope is directly related to its collimation,

that is the alignment of its optical system. Your telescope was collimated at the

factory after it was completely assembled. However, if the telescope is dropped

or jarred severely during transport, it may have to be collimated. The only

optical element that may need to be adjusted, or is possible, is the tilt of the

secondary mirror.

To check the collimation of your telescope you will need a light source. A bright

star near the zenith is ideal since there is a minimal amount of atmospheric

distortion. Make sure that tracking is on so that you won’t have to manually track

the star. Or, if you do not want to power up your telescope, you can use Polaris.

Its position relative to the celestial pole means that it moves very little thus

eliminating the need to manually track it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CGE Pro 1400 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Celestron CGE Pro 1400 Manual

Product: