667041

Celestron CGE Pro 1100 Manual

12
Zoom out
Zoom in
Previous page
1/72
Next page
12
To install the finderscope:
1. Attach the bracket to the optical tube. To do this, place the curved portion of the bracket with the slot over the two holes
in the rear cell. Start threading the screws in by hand and tighten fully with an Allen wrench.
2. Partially thread-in the three nylon thumbscrews that hold the finder in place inside the bracket. Tighten the screws until
the nylon heads are flush with the inner diameter of the bracket ring. Do NOT thread them in completely or they will
interfere with the placement of the finder. (Having the screws in place when the finder is installed will be easier than
trying to insert the screws after the finder has been installed.)
3. Slide the rubber O-ring over the back of the finder (it will NOT fit over the objective end of the finder). It may need to be
stretched a little. Once on the main body of the finder, slide it up about one inch from the end of the finder.
4. Rotate the finder until one cross hair is parallel to the R.A. axis and the other is parallel to the DEC axis.
5. Slide the eyepiece end of the finder into the front of the bracket.
6. Slightly tighten the three nylon thumbscrews on the front ring of the bracket to hold the finder in place.
7. Once on, push the finder back until the O-ring is snug inside the back ring of the finder bracket.
8. Hand tighten the three nylon tipped thumbscrews until snug.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
t
t
h
h
e
e
C
C
G
G
E
E
P
P
r
r
o
o
1
1
1
1
0
0
0
0
&
&
1
1
4
4
0
0
0
0
F
F
i
i
n
n
d
d
e
e
r
r
s
s
c
c
o
o
p
p
e
e
The CGE Pro 1100 and 1400 telescope comes with a 9x50 finderscope. The specifications for a finderscope stand for the
magnification and the aperture, in millimeters, of the scope. So, a 9x50 finder magnifies objects nine times and has a 50mm objective
lens.
Finderscope Installation
The finderscope must first be mounted in the included quick-release bracket then attached to the rear cell of the telescope.
To install the finderscope:
1. Locate the finderscope mounting bracket attached to the bottom portion of the finder bracket. Loosen the two thumb
screws to slide the mounting bracket from the finderscope bracket.
2. Find the two holes in the rear cell of the telescope on the top left, when looking from the back of the tube.
3. Place the mounting bracket over the two holes of the rear cell as shown in the figure 2-10.
4. Insert the screws through the bracket and into the rear cell.
WARNING: If you remove the mounting bracket, do not completely thread the screws back into the rear cell of the telescope.
The screws may be long enough to obstruct the movement of, and
possibly damage the primary mirror.
With the bracket firmly attached to the telescope, you are ready
to attach the finder to the bracket.
1. Slide the O-Ring over the back of the finderscope and
position it on the tube toward the objective end of the
finderscope.
Figure
2
-
11
Alignment Screws
Pivot
Screw
Quick release
Screws
Figure 2
-
1
2
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CGE Pro 1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CGE Pro 1100 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info