580482

Celestron AstroMaster 90 EQ Manual

23
Zoom out
Zoom in
Previous page
1/32
Next page
23
M
M
o
o
t
t
o
o
r
r
D
D
r
r
i
i
v
v
e
e
To allow tracking of celestial objects, Celestron offers a single axis DC motor drive for the AstroMaster equatorial
mount. Once polar aligned, the motor drive will accurately track objects in Right Ascension as they move across the
sky. Only minor adjustments in Declination will be necessary to keep celestial objects centered in the eyepiece for long
periods of time. Models # 21069 and # 31051 come standard with this motor drive and it is attached to the mount but
you will have to remove it to install the battery (remove the motor drive by doing the reverse of the installation
instructions and install the battery per information below and then reinstall the motor drive). The motor drive is sold as
an optional accessory (Model # 93514) for other models.
Installation of the Motor Drive – for those purchasing it as an optional accessory.
The motor drive attaches to the AstroMaster equatorial mount via a flexible coupler that mounts to the R.A. slow motion
shaft and a motor bracket that holds the motor in place. To install the motor drive see the description and photos below:
1. Make sure the R.A. slow motion cable is attached to the R.A. shaft opposite of the latitude scale.
2. Remove the Allen head bolt located on the side of the polar shaft.
3. Slide the open end of the flexible motor coupler over the R.A. shaft. Make sure that the screw on the flexible
motor coupler is positioned over the flat portion of the R.A. shaft.
4. Tighten the motor coupler screw with a flathead screwdriver.
5. Rotate the motor on the shaft until the slotted cutout on the motor bracket aligns with the threaded hole in the
center of the mount’s latitude pivot axis.
6. Place the Allen head bolt through the motor bracket and thread it into the hole on the side of the pivot axis.
Then, tighten the bolt with an Allen wrench.
Figure 4-11 Figure 4-12
Operating the Motor Drive
The motor drive is powered by one 9-volt alkaline battery. This can power the drive for up to 40 hours, depending on
motor speed setting and ambient temperature. To install the battery, unscrew the two mounting screws – Figure 4-11.
Remove the control panel plate from the motor assembly and then remove the motor bracket from the motor. Then, you
will be able to get to the battery connected to cables for installing or replacing. Finally, reverse all steps to remount the
motor drive to the mount.
The motor drive is equipped with a speed rate regulator (in Figure 4-11 it is above the mounting screw) that allows the
motor drive to track at a faster or slower speed. This is useful when observing non-stellar objects like the moon or Sun
which travel at a slightly different rate than the stars. To change the speed of the motor, slide the On/Off switch to the
“ON” position and the red power indicator light will illuminate. Then, turn the speed rate regulator knob clockwise to
increase the speed of the motor and counterclockwise to decrease the speed.
To determine the proper rate of speed, the telescope should be roughly polar aligned. Find a star on the celestial equator
(approx. 0° declination) and center it in a low power eyepiece. Turn the drive on and let the telescope track for 1 or 2
minutes. If after a few minutes, the star drifts to the West, the motor is tracking too slowly and you should increase the
motor speed. If the star is drifting to the East, then decrease the motor speed. Repeat this process until the star remains
centered in the eyepiece for several minutes. Remember to ignore any star drift in declination.
The drive also has a “N/S” switch to be set if operating in the Northern or Southern Hemisphere.
Motor Coupler
Motor Bracket
and Allen Bolt
Behind motor
Mounting
Screws
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron AstroMaster 90 EQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron AstroMaster 90 EQ in the language / languages: English as an attachment in your email.

The manual is 10 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Celestron AstroMaster 90 EQ

Celestron AstroMaster 90 EQ User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info