667044

Celestron Astro Fi Manual

5
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH | 5
Astro Fi TELESCOPE
5. Once the object is centered in your 25 mm eyepiece, turn on
the Red Dot Finder by rotating the power switch knob on the
right side of the finder clockwise. You will hear an audible click
to confirm that the finder has been turned on. This knob also
controls the brightness of the red dot. Turn the knob all the way
to the end to make the dot as bright as possible.
6. With your head positioned about a foot behind the finder, look
through the round window of the finder and locate the red dot.
It will probably be close to, but not on top of, the object you see
when you are looking through the 25 mm eyepiece.
7. Without moving the telescope, use the two adjustment knobs
located on the side and underneath the StarPointer finderscope
(Figure 8). One controls the left-right motion of the dot. The
other controls the up-down motion of the dot. Adjust both until
the red dot appears over the object you are observing in the
25 mm eyepiece.
Your StarPointer Finder is now aligned!
NOTE: Be sure to turn off the Starpointer Finder when not in use to conserve battery power.
ALIGNING THE STARPOINTER FINDERSCOPE
The first time you assemble your telescope, you’ll need to align the StarPointer finderscope with the main optics of the
telescope. This step can be done without powering on the telescope. Although this step can be done out in the field
at night, it is significantly easier to accomplish this outdoors in daylight. Once you have completed the finderscope
alignment, you should not have to repeat this step unless the finderscope is bumped or dropped.
1. Take the telescope outside during the day and, using your naked eye, find an easily recognizable object, such as
a streetlight, car license plate, or tall tree. The object should be as far away as possible, but preferably at least a
quarter mile away.
2. Remove the main dust cover from the front of the telescope by pulling it straight off. Make sure your 25 mm eyepiece
is installed in the focuser.
3. Do not try to move the telescope left and right while it is off. Move the assembled tripod so the telescope is pointed
in the direction of the object you chose in step 1.
4. Look through the telescope and move it up and down until the object you chose lies in the center of the view. If the
image is blurry, gently turn the focus knobs on either side of the telescope until it comes into sharp focus.
NOTE: The image you see in the eyepiece will appear mirror reversed. This is perfectly normal in an astronomical telescope.
GET READY TO OBSERVE
Now that your telescope is assembled and the StarPointer is aligned, let’s connect it to your smartphone or tablet.
We recommend you familiarize yourself with the telescope and app during the day before using it at night.
CAUTION: Remember to never point the telescope at the Sun during the day without using a proper full aperture solar filter!
1. Plug the battery pack into the power port on the base of the telescope, (Figure 9). The red WiFi light on the arm will light,
indicating power and WiFi-ready status. Make sure the small switch near the power socket is in the LEFT position as
shown in the figure.
2. Go to your device’s WiFi settings, and connect to the “Celestron-xx” network. Wait for your device to confirm that you
have successfully connected.
Fig. 8
Up/Down
Adjustment Knob
Power/Brightness Knob
Left/Right
Adjustment Knob
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron Astro Fi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron Astro Fi in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info