580477

Celestron Ambassador 80AZ Manual

8
Zoom out
Zoom in
Previous page
1/66
Next page
8
M
M
o
o
v
v
i
i
n
n
g
g
t
t
h
h
e
e
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
M
M
a
a
n
n
u
u
a
a
l
l
l
l
y
y
The Ambassador mount is easy to move wherever you want to point it.
The up and down (altitude) is controlled by the altitude lock (Figure 2-12).
Loosen the altitude lock by turning it counterclockwise and when at the
desired location tighten the lock by turning it clockwise.
Note: Before tightening the altitude lock all the way on the 80mm, the target
object you are seeking should be located in the finderscope.
Figure 2-12
The side-to-side (azimuth) motion is controlled by the azimuth locking knob
(Figure 2-13). Loosen the azimuth locking knob by turning it
counterclockwise and when at the desired location tighten the lock.
Figure 2-13
When both knobs are loose you can find your objects easily and then lock
the controls. The images are shown for the 50mm and the 80mm are similar.
Note: If the up/down (altitude) motion appears too stiff or too loose, you
can adjust the tension. To do this, you can tighten or loosen the round knobs
(one on each side of the mount directly across from each other). Make sure
the locks in both axes are tight to begin. Hold both round knobs at the same
time and turn them slightly to loosen or tighten them. Then release the
altitude lock and check the tension. Keep adjusting the knobs until the
tension is satisfactory to you. The round knob is located directly above the
altitude lock as seen in Figure 2-12a.
Figure 2-12a
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
a
a
n
n
d
d
A
A
l
l
i
i
g
g
n
n
i
i
n
n
g
g
t
t
h
h
e
e
F
F
i
i
n
n
d
d
e
e
r
r
s
s
c
c
o
o
p
p
e
e
–
–
8
8
0
0
m
m
m
m
m
m
o
o
d
d
e
e
l
l
A finderscope is a very small telescope mounted on the main telescope to make it easier to locate objects.
To install the finderscope:
1. Figure 2-14 shows the finderscope (at top) and the brackets with
mounting screws.
2. Mount the brackets in the holes on the optical tube (Figure 2-15) with
the thumbscrews and tighten. The mounted brackets are shown in
Figure 2-16.
3. Remove the lens caps from both ends of the Finderscope.
4. Put the finderscope inside the mounting brackets with the larger
diameter lens (objective end) facing towards the front (objective lens) of
the optical tube. You will need to back up the screws in the brackets so
the finderscope will fit inside them.
5. The Finderscope should be fit into the brackets where the thumbscrews
can be tightened inside the small grooves in the finderscope. Then,
hand tighten the thumbscrews. Figure 2-14
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron Ambassador 80AZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron Ambassador 80AZ in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 8,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info