580471
6
Zoom out
Zoom in
Previous page
1/35
Next page
4
assembly
The LCM comes partially assembled and can be operational
in a matter of minutes. The LCM is conveniently packaged
in one reusable shipping carton that contains the following
accessories:
• 25mmand9mmEyepieces
• ErectImageDiagonal(60/70/80/90LCMonly)
• StarPointerFinderscope
• AccessoryTray
• The SkyX Student Edition Astronomy Software
• LCMHandControlw/4,000ObjectDatabase
aSSeMbLing The TeLeSCope
Your LCM comes in three major sections: the optical tube,
the motorized mount and the tripod. These sections can be
attached in seconds using the quick release coupling screw
located under the tripod mounting platform and the dovetail
mounting clamp located on the outside of the motorized base.
To begin, remove all of the accessories from their individual
boxes. Remember to save all of the containers so that they can
be used to transport the telescope. Before attaching the visual
accessories, the telescope tube and mount should be attached
to the tripod. First, install the accessory tray onto the
tripod legs:
1. Remove the tripod from the box and spread the legs apart
until the center leg brace is fully extended.
2. Locate the accessory tray, and place it on top of the tripod
center support brace in between the tripod legs
(seegure2-1).
3. Rotate the accessory tray so that the central hole in the
tray slides over the flange post in the center of the
support bracket.
4. Finally, rotate the tray so that the locking tabs slide under the
locking clips on center leg brace. You will feel the tray snap
into place.
It is a good idea to level the tripod by adjusting the height of
the tripod legs before attaching the motorized base and tube.
Minor adjustments can be made later. To adjust the height of
the tripod legs:
1. Lift the tripod leg locking lever located on the side of
each leg.
2. Slide the inner portion of each leg down 6” to 8” inches.
3. Adjust the tripod height until the base is visually level and
press down the locking levers to secure into place.
Attaching the Hand Control Holder
The LCM comes with a snap-on hand control holder that
conveniently attaches to any of the tripod legs. To attach the hand
control holder simply position the holder with the square plastic
tab facing up and push against the tripod leg until it snaps in
to place.
Attaching the Motorized Base to the Tripod
With the tripod properly assembled, the motorized base can
easily be attached using the quick release coupling screw
located underneath the tripod mounting platform:
1. Place the motorized base on top of the tripod making sure
that the three round feet rest on the round flat pads on the
inside of the tripod head.
2. Thread the coupling screw into the hole at the bottom of the
motorized base and hand tighten.
Figure 2-1
Flange Post
Locking Tabs
Locking
Clips
Figure 2-4
Motorized
Base
Tripod
Mounting
Platform
Coupling
Screw
Figure 2-3
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron 80LCM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron 80LCM in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Celestron 80LCM

Celestron 80LCM User Manual - German - 38 pages

Celestron 80LCM User Manual - French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info