666992
9
Zoom out
Zoom in
Previous page
1/100
Next page
ENGLISH I 9
INSTALLING THE DIAGONAL AND EYEPIECE
The diagonal is a prism that diverts the light at a right angle to the light path of the telescope. This allows you to observe
in a position that is more comfortable than if you had to look straight through. The Travel Scope diagonal is an erect image
model that corrects the image to be right side up and oriented correctly left-to-right which is much easier to use for terrestrial
observing. Also, the diagonal can be rotated to any position which is most favorable for you. To install the diagonal and
eyepiece:
1. Make sure the two thumbscrews on the rear of the telescope
tube do not protrude into the opening before installation, the
plug up cap is removed from the opening at the rear of the
telescope tube, and the caps are removed from the barrels on
the diagonal. Insert the small barrel of the diagonal all the way
into the rear opening of the telescope tube (Figure 11). Then
tighten the two thumbscrews.
2. Put the chrome barrel end of one of the eyepieces into the
diagonal and tighten the thumb screw. When doing this make
sure the thumbscrew is not protruding into the diagonal before
inserting the eyepiece.
3.
The eyepieces can be changed to other focal lengths by
reversing the procedure in step 2 above.
Fig. 11
INSTALLING THE FINDERSCOPE (TRAVEL SCOPE 70 ONLY)
1. Locate the finderscope (it will be mounted in the finderscope
bracket).
2. Remove the knurled nuts on the threaded posts on the
telescope tube (Figure 12).
3. Mount the finderscope bracket by placing it over the posts
protruding from the optical tube and then holding it in place
thread on the knurled nuts and tightening them down.
4. Note that the finderscope should be oriented so that the larger
diameter lens is facing toward the front of the telescope tube.
5. Remove the lens caps from both ends of the finderscope.
ALIGNING THE FINDERSCOPE
1. Locate a distant daytime object and center it in the low power (20 mm) eyepiece in the main telescope.
2. Look through the finderscope (the eyepiece end of the finderscope) and take notice of the position of the same object.
3. Without moving the main telescope, turn the adjustment thumbscrews (figure 12) located around the finderscope bracket
until the crosshairs of the finderscope are centered on the object chosen with the main telescope.
4. If the image through the finderscope is out of focus, rotate the eyepiece of the finderscope for a clear view.
Note: Objects viewed through a finderscope are upside down and backwards which is normal.
Fig. 12
Finderscope
Bracket
Finderscope
Eyepiece
Adjustment
Screws
Knurled
Nuts
Objective Lens
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron 21035 - Travel Scope 70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron 21035 - Travel Scope 70 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info