753604

Cecotec Conga 5090 Manual

22
Zoom out
Zoom in
Previous page
1/85
Next page
4342
ENGLISH ENGLISH
Wet & dry tank
1. Take out the Wet & Dry tank.
2. Separate the dust compartment from the rest of the tank.
3. Open dust compartment and empty it.
4. Use the cleaning brush to clean the inside of the dust tank.
5. Assemble the dust compartment in the Wet & Dry tank.
6. Install the Wet & Dry tank back in the robot.
7. If the Scrubbing mode has been used, empty the water tank and then fill it with clean water
to rinse it. Empty it again before installing it back in the robot.
Fig. 29
High-efficiency filter
1. Remove the high-efficiency filter and shake it to remove all the dust.
Note:
Replace the high-efficiency filter every 3 months depending on the frequency and type of use.
2. Clean the filter periodically with a brush to avoid blockage. Do not use water or detergents.
Fig. 30
Side brush
Remove and clean the side brushes regularly.
Note: In order to ensure a perfect cleaning, it is suggested to replacethe side brushes every 3
months, depending on the frequency and type of use.
Fig. 31
Free-fall sensors
Clean the free-fall sensors with a soft cloth regularly.
Warning: Always transport the product turned off and in its original package.
Fig. 32
8. BATTERY REPLACEMENT AND CHARGING
Do not use any other battery, power adapter or charging base than the one provided officially
by Cecotec.
Do not use non-rechargeable batteries.
Do not remove, dismantle or attempt to repair the battery or the charging base.
Do not place the charging base near heat sources.
Do not use a wet cloth to wipe any of the parts of this product.
If the robot is not going to be used for a long time, remove the battery from the product and
store it in a dry and safe place. It is suggested to charge the battery every month in order to
avoid damage to the battery.
Do not dispose of waste batteries at will. It is suggested to hand them over to professional
organizations for correct treatment.
9. TROUBLESHOOTING
Problem Solution
The robot does not start up or does not
clean.
The robot cannot operate with low battery.
Allow the robot to cool down before operating
it again.
The room temperature is below 0 ºC or above
50 ºC.
Operate the robot in a room where the
temperature is between the stated
temperature range.
The robot cannot charge or return to the
charging base.
There are too many obstacles near the
charging base, relocate the charging base to
an area free of obstacles.
Clean the charging terminals.
Make sure the power switch is turned on.
The robot is too far away from the charging
base, place it closer and try again.
There is very little free space around the
charging base. Make sure the charging
terminals are clean.
The robot does not work properly. Turn the robot off, switch it off and turn it on
again.
The robot emits a strange noise during
cleaning.
The main brush, side brush or omnidirectional
wheel may have foreign matters tangled, stop
the robot and clear it up.
The robot does not clean efficiently or
dust leaks from the robot.
The dust tank is full. Empty it and clear the
high efficiency filter if it is blocked.
The high-efficiency filter is blocked, clear it.
The main brush is tangled with foreign matter,
please clear it up.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cecotec Conga 5090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cecotec Conga 5090 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info