508116
16
Zoom out
Zoom in
Previous page
1/23
Next page
ENG-31
ENG
ENG-30
M2/- M1/+
Setting the measurement unit
Change the unit (km or mile).
* Stop measurement and perform the resetting operation (page 17) before you change
the unit. Unless you perform the resetting operation, DATA RESET appears on
the screen, preventing from changing the unit.
1. Press the MENU button in the measurement screen to
switch to the menu top screen.
Switch to the UnIT screen using the M1/+ and M2/- buttons,
and confirm with the SSE button.
Menu top:
MENU
Changing the menu:
M1/+
M2/-
Confirm:
SSE
2. Select the speed unit using the M1/+ and M2/- buttons.
km mile:
M1/+
M2/-
3. Pressing the MENU button returns to the menu top screen
(UnIT screen), and confirm the change(s).
Pressing it again returns to the measurement screen.
To the menu top/measurement screen:
MENU
* After the unit is switched, the total distance measured in the past is automatically
converted to the new unit.
Total distance manual entry
You can enter any value to the total distance.
The total distance in the past can be input after formatting or to a new computer.
1. Press the MENU button in the measurement screen to
switch to the menu top screen.
Switch to the ODO InPUT screen using the M1/+ and M2/-
buttons, and confirm with the SSE button.
Menu top:
MENU
Changing the menu:
M1/+
M2/-
Confirm:
SSE
2. Enter the total distance using the M1/+ and M2/- buttons,
and move digits using the SSE button.
* The total distance shall be entered with a positive value.
Increase/decrease:
M1/+
M2/-
Move digits:
SSE
(or)
(or)
(or)
Current speed unit
Current total value
(Back)
(Back)
(Back)
(or)
1. Press the MENU button on the measurement screen to
switch to the menu top screen.
Switch to the SEnSOR-ID screen using the M1/+ and M2/-
buttons, and confirm with the SSE button.
Menu top:
MENU
Changing the menu:
M1/+
M2/-
Confirm:
SSE
2. Select the sensor ID to be checked.
Select it from Hr (heart rate sensor), SP1 (speed sensor 1),
and SP2 (speed sensor 2) using the M1/+ and M2/- buttons.
Selecting the sensor:
M1/+
M2/-
3. Check whether the heart rate sensor is worn properly when
you selected Hr, or whether the speed sensor is mounted
properly when you selected SP1 or SP2.
4. Press the SSE button to start searching the ID.
Spin the rear wheel or crank when you selected SP1 or
SP2.
When the heart rate or speed (cadence) is displayed with
ID-OK on the screen, synchronization is completed.
Start searching:
SSE
5. Pressing the MENU button returns to the menu top screen
(SEnSOR-ID screen), and confirm the change(s).
Pressing it again returns to the measurement screen.
To the menu top/measurement screen:
MENU
* This unit enters the search mode for 5 minutes after starting the ID synch.
While ID-SKIP is indicated, press the SSE button in the search mode to cancel
the ID synch, and ID-SKIP is displayed. Unless a sensor signal is received in 5
minutes, ID-ERROR is displayed.
When ID-SKIP or ID-ERROR is displayed, the ID has not been synchronized
properly. In such a case, the sensor ID retains the previous ID setup.
Be sure to check the sensor/mounting condition before you check the ID again.
* SP2 is used when a computer is commonly used for second bicycles. By synchro-
nizing the ID of the second bicycle equipped with a second speed/cadence sensor
and the computer with SP2, re-synchronizing and the computer with SP2, syn-
chronizing the ID is not required every time you move the computer between first
bike to the second bike.
(or)
(or)
(Back)
(Back)
Continue
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye V3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye V3 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cateye V3

Cateye V3 User Manual - German - 23 pages

Cateye V3 User Manual - Dutch - 23 pages

Cateye V3 User Manual - French - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info