Manual Cateye TOMO CC-ST200 (page 2 of 2) (English)

479721

Zoom out

Zoom in

1/2

MEASURING AND DISPLAY FUNCTIONS

OPERATING INSTRUCTIONS

SPD Current Speed

0.0(3.0) - 65 mile/h(27inch) ±1 mile/h under31 miles/h

This is always displayed on the main display and updated once a second.

ODO Total Distance (Odometer) 0.0 - 9999.9 mile ±0.1 mile

This is continuously measured until battery wears down or all clear operation is

done. At 10,000 miles(km), it returns to zero and counting begins anew.

DST Trip Distance 0.00 - 999.99 mile ±0.01 mile

The trip distance from start to current point is displayed. With Reset operation, it

returns to zero.

TM Elapsed Time 0:00'00" - 9:59'59" ±0.003 %

Elapsed time is measured from start to current point, in units of hours, minutes and

seconds. At 10 hours, it returns to zero and counting begins anew. With Reset

operation, it returns to zero.

AVS Average Speed 0.0 - 65.0mile/h ±0.3 mile/h

The average speed from start to current point is displayed within 27 hours 46

minutes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded,

(.E) is displayed and calculation ceases.

MXS Maximum Speed 0.0(3.0) - 65 mile/h(27inch) ±1 mile/h

With Reset operation, it returns to zero and counting begins anew.

12-hour clock time 0:00' - 11:59' ±0.003 %

The current time is displayed by a 12-hour clock.

DST

ODO

DST

AVS

MXS

This function switches the main unit to start or stop automatically, in which AUTO

symbol appears on the screen, and you are free from pressing S/S button each

time.

•How to switch on/off the Auto Function.

In TM, DST or AVS, this function switches on/off with each press of SET button.

When on, AUTO symbol appears. *With this function, it ceases measuring

elapsed time during a stop.

* 2 seconds may be elapsed if mount the main unit to the bracket with this func-

tion on.

AUTO

DST

POWER SAVING FUNCTION

A. Main Display (Speed)

B. Sensor Pulse Symbol

C. Mode Symbol

D. Speed Scale Symbol

E. Auto Mode Symbol

F. Sub-Display (Selected Function)

G. M (Mode) Button

H. S/S (Start/Stop) Button

I. Set Button

J. Battery Case Cover

K. Contact

1. Bracket

2. Wire

3. Sensor

4. Sensor Bands-A (S)(L)

5. Sensor Bands-B

6. Magnet

Sensor Band Rubber Pad

When main unit is left without receiving any signal for 60-70 minutes continuously,

power supply is shut down and main unit will display ( ) only as the figure. By

pressing M button or S/S button, or by receiving signal, this function is released.

AUTO (AUTOMATIC START/STOP) FUNCTION

BUTTON FUNCTION

• M button (Fig.1)

Changes the display in the order shown in fig. 1, and data is displayed on the sub-

display. *If held over 2 seconds, 12-hour clock appears.

• S/S button

Starts and stops the measurement of trip distance and elapsed time. During op-

eration, speed scale symbol flashes. In Auto Function, this button is invalid.

• SET Button

This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear

all present data and any irregularity. When pressed in stop state in each mode, the following can be

revised.

• In ODO mode --------------------- Wheel circumference

• In mode ----------------------- 12-hour clock

• In TM, DST or AVS mode ----- On/off the Auto function

Reset Operation: (Fig.2)

Select any mode except ODO, then press M button and S/S button simulta-

neously. MXS, AVS, DST and TM will become zero. (When done in ODO,

registered wheel circumference will be displayed.)

All Clear Operation: (Fig.3)

When M button, S/S and set buttons are pressed simultaneously, all data

stored (ODO, speed scale, Wheel circumference and clock time) is erased.

All displays illuminate, then mile/h symbol illuminates. This should only be

executed after replacing battery or when irregular display occurs due to

static electricity, etc. Since all memories are erased, set necessary data

again according to "Main Unit Preparation".

Fig.6

Fig.7

Fig.5

MAIN UNIT PREPARATION

The following must be completed before operating.

(1) How to measure wheel circumference (L) of your bike (Fig.4)

Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the

start and the end of the revolution on the ground and then measure the distance

between the two marks. This is your actual circumference. Or, the "Selecting

Values Cross Reference Table" tells you an approximate circumference accord-

ing to tire size.

(2) Setting Speed Scale

Preform all clear operation. All displays will illuminate. Then mile/h alone will be

displayed as illustrated in fig.5. Km/h and mile/h are alternately displayed with

each press of S/S button. Press M button to set desired speed scale. The dis-

play will change as fig. 6.

(3) Setting the wheel circumference (Fig.6)

The standard wheel circumference of 216 cm for 27" wheel is displayed. When

using 216 cm without revision, press M button. ODO will be displayed and 216

cm is set. For revision, press S/S button to increase the number by one. To

increase rapidly, hold down the button. When the desired number appears,

press M button. ODO will be displayed, and the desired number is set.

(4) Resetting or changing the wheel circumference

Set main unit in ODO with M button, and stop it with S/S button. Press SET button. The stored number

will flicker on the sub-display. Revise the number as desired according to the instructions in (3).

Setting the clock time (Fig.7)

Press M button over 2 seconds to select , and stop it with S/S button. Then

press SET button, and minutes flash. Press S/S button to advance minutes by

one. To advance rapidly, hold down the button. Set the time one or two minutes

ahead of the current time. Then press M button, and hours will flash. Use S/S

button the same way. Press SET button to complete time setting. *When you

press the SET button, the undisplayed seconds will turn to zero. For accuracy,

set by the radio time signal.

HOW TO REPLACE THE BATTERY

Turn main unit over, remove battery case cover with coin and insert a

new lithium battery properly (CR1620 or CR1616) with the (+) pole up-

ward (fig.17), and close the cover securely.

* Please make sure to do the All Clear operation after replacing bat-

tery, and to set the unit again.

8. Bracket Rubber Pad (2 pcs.)

9. Wire Securing Tape

10. Sensor Band Screw

MOUNTING TO BIKE

• The spokes must run correctly through the inside the magnet as in fig.8.

• Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diam-

eter (S size for up to 24ø, L for oversize).

1. Insert the band-B into the slit of the band-A, and put the rubber pad inside of the band-A(fig. 9).

Adjust the length in order that the screw-fastening part of the bands are parallel when mounted

to the fork(fig. 10). *To pull out the band B from band A, tug strongly.

2. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the

screw(fig. 11).

3. Align the magnet's center and the sensor's marking line(fig. 12), and make sure of 2mm clear-

ance between the magnet and sensor (fig. 13). Then tighten the screw securely. Cut the excess

of the band-B with a nipper or the like.

• Secure the wire with tape as fig. 14. Wind the wire round the outer cable and adjust length. Loosen

the wire in the area marked with the arrow so that the wire does not hinder handlebar operation.

• Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter. Attach the

bracket close to the handlebar stem (fig. 15).

• Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward

while pushing down the lever. (fig. 16)

•Test (Fig.16)

Mount main unit. If main display does not show any figures, press either M button or S/S button to

release from power saving function. Spin the wheel to check if sensor pulse symbol flashes. If not,

adjust relative positions of magnet and sensor following the instructions.

magnet

sporkes

Fig.8

sensor

band B

sensor

band A

Fig.9

rubber pad

Fig.10

rubber pad

sensor band B

sensor band A

parallel

Fig.11

sensor band A

screw

sensor

fork

Fig.12

markingline

of sensor

center of

magnet

sensor

Fig.13

about 2mm

wire securing

tape

Fig.14

outer cable

wire

bracket

screw cap

Fig.15

rubber pad

lever

Fig.16OPEN

Fig.17

Fig.2

RESET

Fig.3

ALL CLEAR

MXS

ODO

DST

AVS

Fig.1

Fig.4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cateye TOMO CC-ST200 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cateye TOMO CC-ST200 Manual

Product: