Manual Cateye ENDURO 2 - CC-ED200 (page 4 of 4) (English)

637214

Zoom out

Zoom in

1/4

ORIGINAL SET UP FOR THE MITY 3 AND ENDURO 2

L cm

on back

To set up your computer for the first time,

perform an ALL CLEAR OPERATION first

by pressing ALL THREE BUTTONS AT

THE SAME TIME.

Hint: Hold the computer upside down

holding the MODE and START/

STOP (S) Buttons DOWN. Now

PRESS the SET Button with a pencil

or other pointed object.

The complete screen will light up for a mo-

ment and then all fade away. The only

thing on the screen will be a flashing "K".

Select the speed scale you would like by

pressing the MODE Button. "K" for kilome-

ters and "M" for miles per hour. Note that

the speed scale you select DICTATES

CLOCK function in 12 or 24 hours. "K" will

select a 24 hour clock. "M" will select a 12

hour clock.

Set the speed scale by PRESSING the

ST./STOP (S) Button.

The number "210" will flash. This is a pre-

set tire setting for 700X23C tires. Refer to

the tire calibration chart in your manual or

on our web site <www.cateye.com>.

Please note that this number is actually the

DISTANCE in Centimeters your tire rolls

with each revolution while you are on the

bike. If you want to input the most accu-

rate number you will need to do a wheel

roll out.

Increase the digits by PRESSING the

MODE Button. Decrease the number by

PRESSING the ST./STOP (S) Button. Set

the number by PRESSING the SET Button

on the back.

Your computer is now set up for riding.

BUTTON NAVIGATION

The right Button is the MODE Button. The left but-

ton is the START/STOP (S) Button. You use the

MODE Button to navigate through the modes.

From the ELAPSED TIME func-

tion (Tm on the computer

screen), you can PRESS the

MODE Button to access the AV-

ERAGE SPEED function (Av).

PRESS the MODE Button to access the DISTANCE

ONE (Dst1) function. This is the standard ride distance

function. Now PRESS the MODE Button to get back to

the TIME (Tm) function.

Time

2 sec.

Clock

TIME has a sub-function of CLOCK. You

access this by PRESSING and HOLD-

ING the MODE Button for 2 Seconds. To

get out of the CLOCK press the MODE

Button. You are now back in TIME.

AVERAGE SPEED (Av) has a sub-func-

tion of MAXIMUM SPEED (Mx). To ac-

cess MAX SPEED PRESS and HOLD

the MODE Button when in AVERAGE

SPEED. To get out of MAX SPEED

PRESS the MODE Button.

Average

Speed

Max

Speed

Distance

One

Distance

Two

Odometer

DISTANCE ONE (Dst1) has two sub-functions.

PRESS and HOLD the MODE Button for 2 seconds

to access DISTANCE TWO (Dst2).

DISTANCE TWO is a separate Trip Distance that

can be reset without resetting the other functions.

To reset DISTANCE TWO, PRESS and HOLD the

ST./STOP (S) and MODE Button for ONE SEC-

OND.

From DISTANCE TWO (Dst2) you can access the

ODOMETER function (Odo). PRESS and HOLD

the MODE Button for TWO SECONDS in DIS-

TANCE TWO and you will now be in ODOMETER

(Odo.).

To navigate out of either of these two sub-functions

to DISTANCE ONE, press the mode button.

Time

1 sec.

Resetting TIME and DISTANCE

functions

To reset the TIME, DISTANCE

ONE, AVERAGE and MAX

SPEEDS, PRESS AND HOLD

the MODE and ST./STOP (S)

Buttons for ONE SECOND.

DISTANCE TWO (Dst2) can

only be reset while in DIS-

TANCE TWO.

AUTO MODE

You can set the computer to record TIME,

DISTANCE, MAX and AVERAGE SPEED

automatically (AUTO MODE) or manually

(STANDARD MODE).

In STANDARD MODE you must press the

ST./STOP (S) Button to begin recording

TIME and DISTANCE.

In AUTO MODE (AT) the computer starts

and stops when ever it records a signal

from the sensor at the wheel.

To set the computer to AUTO MODE with

the computer in the DISTANCE function or

TIME function, press the SET Button on

the back of the computer. A small symbol

with the letters AT will appear on the

screen indicating AUTO MODE. You take

the computer out of AUTO MODE the

same way.

Setting the CLOCK

To set the CLOCK the computer must be

turned off and the speed scale symbol (ei-

ther M for Miles or K for Kilometers) must

not be flashing. In the Time function

PRESS AND HOLD the MODE Button.

You will see little CLOCK symbol. Now

PRESS the SET Button on the back of the

computer. The hours will start flashing.

The MODE Button advances the digits.

The ST./STOP (S) Button changes from

Hours to Minutes. PRESS the SET Button

on the back to set the CLOCK.

The CLOCK is set to either 24 HOUR or 12

HOUR depending on the SPEED SCALE

selected. In K (Kilometers per hour) a 24

HOUR CLOCK is selected. In M (Mile per

hour) a 12 HOUR CLOCK is selected.

Moving TIME, AVERAGE and

MAX SPEED to upper display

When the computer is set in AUTO MODE

(AT), the functions of TIME, AVERAGE

and MAX SPEED can be switched to the

upper display by PRESSING the ST./

STOP (S) Button. You can move SPEED

back to the upper display by pressing the

ST./STOP (S) Button again.

In STANDARD MODE (AT sym-

bol is off) PRESS and HOLD

ST./STOP (S) Button for 2 sec-

onds.

WHEEL SETTING A or B

The computer has two wheel settings for

quickly and conveniently moving the be-

tween two bikes with different size of tires.

You can tell which WHEEL SETTING you

are in by the semicircle symbol with an "A"

or "B" on the computer screen. Wheel set-

ting "A" has been preset with a tire size for a

700 X 23C road tire. Wheel setting "B" is

preset for a mountain bike tire of 26 x 1.95.

Wheel setting "B" is also specifically pro-

gramed for low speed sensitivity. If you are

using the computer on a mountain bike we

recommend that you use Wheel setting "B".

To select Wheel setting "A" or "B", HOLD

the SET Button except in ODOMETER

function.

CHANGING the WHEEL SETTING

CALIBRATION NUMBER

When you are in the ODOMETER (Odo)

function, you can view the WHEEL CALI-

BRATION NUMBER by PRESSING the

ST./STOP (S) and the MODE Button.

To change the CALIBRATION NUMBER

PRESS the SET Button on the back of the

computer in ODOMETER (Odo) function.

The WHEEL CALIBRATION NUMBER will

flash on the screen. PRESS the MODE

Button to increase the digits. PRESS the

ST./STOP (S) button to decrease the dig-

its. PRESS the SET Button on the back to

set the new number.

REPLACING MILEAGE INTO THE

ODOMETER

This is done after replacing the battery in

the unit or for transferring mileage from

another computer.

First PRESS ALL THREE BUTTONS, the

MODE Button, the ST./STOP (S) Button

and the SET Button on the back. Now the

"K" flashes indicating speed scale.

PRESS the MODE Button to select be-

tween "K" for Kilometers or "M" for Miles

per hour reading.

To add previous mileage or kilometers you

must NOW PRESS AND HOLD the MODE

Button. ".0" will be flashing. Input the

number with the MODE Button. PRESS

the ST./STOP (S) Button to change to the

next digit. You will be able to set distance

up to 00,000.0 digits. Now press the SET

Button on the back.

Now you must input your tire calibration

number. Please note that this number is

actually the DISTANCE in Centimeters

your tire rolls with each revolution while

you are on the bike.

on back

DISTANCE, AVERAGE

or TIME function

K (km/h)= 24hr. clock

M (mph)= 12hr. clock

on back

advance the digits

change from Hours

to Minutes

Time

on back

Clock

STOP

STATE

STOP

STATE

Odometer

decrease the digits

increase the digits

change to the next

digit

Input the number

decrease the digits

increase the digits

SET UP

FOR

RIDING

ALL CLEAR

OPERATION

SET button

MODE button

ST./STOP

button (S)

ST./STOP(S) MODE

2 sec.

on back

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cateye ENDURO 2 - CC-ED200 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cateye ENDURO 2 - CC-ED200 Manual

Product: