538694

Cateye CC-VL200 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
SET
(
on back
)
Selects the flickering digits
Hour Minute Return to Measuring
Increases the figure
Rapidly increases the figure
O
do
A
v
T
m
D
st
SET
(
on back
)
Moves to the next
Resets data
In display:
Clock Time Setting
In Odo display:
Wheel Circumference Setting
In display:
Enters power saving function
In Odo display:
No change
SET
(
on back
)
Completes setting
Return to measuring
Increases the figure
Rapidly increases the figure
L
SET
(
on back
)
Press simultaneously
Using the unit
for the first time
All Clear Operation
Press Main button and SET button simultaneously.
→All displays illuminate, and then "Km" symbol flashes.
Speed Scale Selection
Press Main button and select "Km" or "Mile".
Wheel Circumference Setting
Increase the figure by Main button
(to increase rapidly, hold down the button).
Press SET button to fix it
Press SET button to fix it
Preparation Completed
Set the Clock time
After replacing
battery
Odo Data Input
Hold down Main button to
select Odo input display.
Input the figure by Main button
Press SET button to change the flickering digit.
MAIN UNIT PREPARATION
In Wheel Circumference
Setting Display:
In Clock TIme Setting Display
In Ordinary Display
All Clear Operation
Precautions
• Don't pay too much attention to your computer functions while riding. Keep your eyes on the
road and give due consideration to safe riding.
• Securely attach the magnet, sensor and bracket to your bicycle. Periodically check if the screws
and secure bands have loosend.
• Safely dispose of the old battery. Do not place it within children's reach. If swallowed by mistake,
consult a doctor immediately.
• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.
• For cleaning, use neutral detergent on soft cloth, and wipe off with dry cloth. Do not apply paint
thinner, benzine or alcohol, to avoid damages on the surface.
• If there is mud, sand or the like clogged between the button and the body, the movement of the
button may be deteriorated. Softly wash away such objects with water.
Spd Current Speed
0.0(3.0) - 65mph ±1 mph (under 31 mph) [0.0(4.0) - 105 km/h ±1 km/h]
Aways displayed on the upper display and updated once a second.
Average Pace Arrow
Shows whether the current speed is faster or slower than the average speed
----- Faster than the average speed
----- Slower than the average speed
Odo Total Distance (Odometer) 0.0 - 9999.9 mile[km] ±0.1 mile[km]
Continuously measured until battery wears down. At 9999.9 km, it returns to zero
and counting begins anew. (With all clear operation, it return to zero; to continue
accumulation of data, input the previous Odo data after all clear operation.)
Dst Trip Distance 0.00 - 999.99 mile[km] ±0.01 mile[km]
The trip distance from start to current point is displayed. With reset operation, it
returns to zero.
Tm Elapsed Time 0:00'00" - 9:59'59" ±0.003 %
Elapsed time is measured from start to current point, in units of hours, minutes and
seconds. At 10 hours, it returns to zero and counting begins anew. With reset opera-
tion, it returns to zero.
Av Average Speed 0.0 - 63.0 mph[99.9km/h] ±0.3 mile[km]
The average speed from start to current point is displayed. If the elapsed time ex-
ceeds 10 hours, (.E) is displayed and calculation ceases.
Clock time 1:00' - 12:59' or 0:00' - 23:59' ±0.003 %
If "Mile" is selected for scale symbol, the clock time is in 12 -hour. If "Km", the clock
time is 24-hour.
Power Saving Function
When the main unit does not receive a signal, or a button has not been pressed for
1~2 hours, the power supply is shut down and the main unit will only display the
clock . By pressing the Main button, or by receiving signal, this function is re-
leased.
Trouble Shooting
No display.
Has the battery in the main unit worn out?
Replace it with a new one.
Incorrect data appears.
Do "All Clear" operation.(If possible, write down the Odo data before all clear operation, and
input it again after the display returns normal.)
Current speed does not appear. (When current speed does not appear, first short-circuit the
contact on the back with metal; if the speed display appears, the main unit is normal and the
problem must be in the bracket or the sensor.)
Is there anything on the contact of the main unit or of the bracket?
Wipe the contact clean.
Is the distance between the sensor and the magnet too far?
Are the marking line of the sensor and the center of magnet aligned?
Adjust the position of the sensor and magnet again.
Is the wire broken?
Replace it with a new one.
Current speed does not appear in wet condition.
Wipe the contacts with dry cloth. Contacts can also be treated with a water repellent silicon
jell from an automotive parts store or hardware store. Do not use industrial water repellent; it
may damage the bracket.
When "Mile" was chosen for speed scale,
the clock time is in 12-hour. If "Km", the clock
time is 24-hour.
How to Replace Battery
In order to continue accumulation of Odo data, write down the stored
Odo data before replacing the battery. Insert a new lithium battery
(CR2032) with the (+) pole upward.
Continuing Accumulation of Odo Data
Although the Odo data returns to zero by all clear operation, you can
continue accumulation of data by inputting the previous Odo data. Be
sure to write down the data before replacing the battery.
Measure the wheel
circumference by traveling
your bike on the ground for
one full wheel revolution. Or
"Selecting Values Cross
Reference Table" tells you an
approximate circumference
according to your tire size.
A. Speed Display
B. Mode Symbol
C. Average Pace Arrow
D. Speed Scale
E. Velocity Indicator
F. Sub-Display (Selected Function)
G.Main Button
H. SET Button
I. Battery Case Cover
J. Contact
Specifications
Applicable Wheel Circumference 112cm - 255cm (initial figure: 205 cm)
The length of the wire 70cm
Power Supply Lithium Battery (CR2032) x 1
Battery Life Approx. 3 years(The life of the first factory-loaded battery may be shorter than this
period.)
Dimension/Weight 1-25/32” x 1-9/16” x 5/8” [45 x 40 x 15.5 mm ] / 0.88oz. [25 g]
* The specifications and design are subject to change without notice.
1Bracket
2Wire
3Sensor
4Magnet
5Rubber Pad
6Nylon Ties
When you start/stop riding, the unit automatically starts/
stops measuring.
While measuring, the Velocity Indicator rotates.
HOW TO INSTALL
nylon tie
magnet
spoke
sensor
sensor's
marking
line
magnet's
center
front fork
brake cable
wire
nylon ties
bracket
rubber pad
handlebar
lever
Aline the magnet’s center
and the sensor’s marking
line. Make sure of 2mm
clearance between the
magnet and sensor. Tem-
porality attach the sensor to
the fork with the self-adhe-
sive patch.
Test
Slide the main unit onto the bracket
according to “How to Attach Main
Unit to Bracket” (below). Spin the
front wheel and check if the velocity
indicator is spinning. (If not, adjust
the relative positions of the magnet
and sensor again.) After the test, re-
move the main unit.
Fix the sensor with the nylon ties.
Note: Fasten the ties securely.
Secure the wire along the fork
with the nylon ties, and wind it
round the brake cable up to the
handlebar.
Note: Allow enough wire length
in the area marked with
in the illustration, to
insure full movement and
unhindered operation of
the handlebar.
Slide the main
unit onto the
bracket from front until
it clicks into position. To
remove it, pull it off forward
while pushing down the lever.
Just press Hold down
Button Operation
pull
clearance 2mm
open
close
slide
How to Attach Main Unit to Bracket
2
3
4
51
OPERATING INSTRUCTIONS
E
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-VL200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-VL200 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info