471843

Cateye CC-TR100 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
CC-TR100
3938
CC-TR100
MODE-
1
MODE-
2
MODE-
1
MODE-
2
Haert rate sensor ID menu screen
Data storage menu screen
Heart rate zone menu screen
MODE-
1
MODE-
2
MODE-
1
MODE-
2
Data file menu screen
For the basic information on how to use the
menu screen, refer to page 28.
MODE-
1
or
MODE-
2
S/S/E
S/S/E
Data file
You can check and manage data files recorded by the TR100.
Display 1 indicates the remaining amount of storage (%). Display 3 indicates the total number
of laps used in that data file. Display 4 indicates the data file number.
NOTE: • To view and use the contents of the stored data files, the optional download kit (and
or power unit) is required.
• When there are no date files recorded (“F-0” on Display 4), this screen cannot be
operated.
Remaining memory
Data file
number
Number of laps used
Data file menu screen
• Checking data files
You can check data files by pressing the START/STOP/ENTER button.
The screen displays the data file number, recording interval, memory consumption, number
of laps, date and time when the file was recorded, and exercise duration.
To switch the data file number, press MODE-1 or MODE-2.
NOTE: • Up to 99 data files can be stored until the remaining memory is at 0%.
• When the remaining memory reaches 0% while data storge is in progress, your
data file will end at that point. Measurement continues, however, data is no longer
stored in a data file. New data files will not be created.
• When data is transferred to a personal computer using the optional download kit,
“move data” is performed and the data files are deleted from the TR100.
(“Move data” can be changed to “Copy data”. For details, see the instruction manual
for the download kit.)
Alternating data display
Switch file
End
Memory consumption
Recording interval
Number of
laps used
in file
Date of ride
Ride time
Ride start time
Data file check screen
File number
For the basic information on how to use the
menu screen, refer to page 28.
S/S/E
S/S/E
Heart rate sensor ID
This function allows the ID signal transmitted by the heart rate sensor to be received and
checked.
Before checking HR sensor ID, mount the main unit to the HR receiver.
NOTE: Be sure to attach the main unit to the HR receiver. Signals from the heart rate sensor
cannot be received by the main unit alone.
Within 5 minutes of pressing the START/STOP/ENTER button, place the HR sensor approxi-
mately 20-80 cm from the main unit and press the reset button on the HR sensor for five
seconds to transmit the ID signal.
When the main unit receives the ID signal, the ID check has been completed.
You can view the ID number but cannot reset it while the bicycle is in motion.
NOTE: • Failure to receive the ID signal within five minutes or the pressing of the START/
STOP/ENTER button cancels the heart rate sensor ID set mode, leaving the ID as it
was.
• The minimum transmission of the heart rate sensor is 20 cm. The signal will be too
strong to perform the heart rate sensor ID check if the chest strap is within 20 cm of
the main unit.
• When two or more users with this unit ride side by side with the same ID, interfer-
ence can occur and correct measurement may be impeded. In such a case, change
the ID using the following the steps below:
After ID checking, the ID viewing screen reappears automatically.
Heart rate sensor reset button
ID standby screen
5 Sec
Cancel
Heart rate sensor ID menu screen
Present ID number
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-TR100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-TR100 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info