471843

Cateye CC-TR100 Manual

8
Zoom out
Zoom in
Previous page
1/28
Next page
CC-TR100
1312
CC-TR100
MODE-
1
or
MODE-
2
M
K
S/S/E
5. Tire circumference input
Enter the circumference of the tire of your bicycle in mm. 2096 mm (700 x 23 C) is preset as
the initial value. To change the value, use the MODE-2 button to increase the value, and use the
MODE-1 button to shift the digit selected.
Pressing the START/STOP/ENTER button and this is the last step in the initial set-up.
Adjustable range: 0100 to 3999 mm
NOTE: • You can find your approximate tire size on the tire circumference chart on page 53.
• When a value outside the adjustable range is entered, an error indication appears on
the screen and you cannot select the value.
MODE-
1
MODE-
1
MODE-
2
S/S/E
6. Operation test
Test the functioning of the speed sensor, cadence sensor, and remote buttons with the main
unit attached to the receiver.
1. Raise the rear wheel and spin the tire, and make sure that the speed (Display 1) shows a
number greater than zero.
2. Turn the crank (backpedal) and make sure that the cadence (Display 3) shows a number
greater than zero.
OK
OK
NOTE: If the screen remains at “0”, the relative positions of the magnets to the sensors
may be inappropriate. Follow the instructions given in “Installing the unit on your
bicycle”, on page 8.
3. Press the right and left remote buttons to check that you can operate the main unit with
them.
NOTE: • If the button is not operable, it indicates that the main unit and/or the button
connector may not have been installed properly.
• In the initial setup, the MODE-1 and MODE-2 button functions have been speci-
fied. To change the settings, see “Defining remote button setting” on page 33.
Completion of initial set-up
When the setup is completed, set the date and time as described in “Configuring main unit”
on page 28.
Display-1Rotate the rear wheel Display-3Rotate the crank arm
Changing a value
Select
Increases the value
Shifting the digit
3. Checking heart rate sensor ID
The heart rate sensor ID must be checked within five minutes after the formatting or restarting
operation.
Before performing an ID check, mount the main unit to the HR receiver.
NOTE: Be sure to attach the main unit to the HR receiver. Signals from the heart rate sensor
cannot be received by the main unit alone.
Place the heart rate sensor approximately 20-80 cm from the main unit, and press the reset
button of the HR sensor for five seconds. The main unit will receive the signal from the heart
rate sensor, and will start checking the heart rate sensor ID. When the check is completed, the
ID number is displayed, followed by the next screen.
NOTE: If the HR sensor is placed too close to the main unit (within 20 cm), the main unit
cannot receive the ID signal. If an ID check failed, change the distance, and reset the
heart rate sensor.
If “E” appears on Display-2, or a HR sensor ID check failed even at a proper distance,
the batteries may be dead. Replace the batteries of the heart rate sensor in the proce-
dure shown on page 48, and format (restart) the computer again.
Pressing the reset
button for five seconds
Select
Switch
For formatting
4. Selecting speed
unit
For restarting
Ready
4. Selecting speed unit
The default speed unit is “km/h.”
By pressing the MODE-1 or MODE-2 button, you can switch the unit between “K (km/h)” and
“M (miles/h).” Select the desired speed unit, and press the START/STOP/ENTER button. The
selected unit is now accepted, and the tire circumference screen appears.
Attach the main unit to
the receiver.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-TR100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-TR100 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info