580402

Cateye CC-GL51 Stealth evo plus Manual

45
Zoom out
Zoom in
Previous page
1/47
Next page
45
Introduction
How to install the
unit on your bicycle
Setting up the
computer
How to use the
computer
Setup of your PC
Uploading the
measurement data
Changing the
computer
configuration
Others
How to install the heart rate sensor (HR-11)
Heart rate is measured when the heart rate sensor is worn on the chest.
Warning!!! : This product must NOT be used by those who have a pacemaker.
• To avoid measurement errors, it is recommended to moisten the electrode pads with water.
• If your skin is sensitive, the electrode pad may be moistened with water and worn on a thin
undershirt.
• Chest hair may interfere with the measurement.
1
Attach the heart rate sensor to the HR strap.
Push it in until it clicks.
2
Insert the HR strap hook to the other end of the strap.
Wear the heart rate sensor with the HR strap, and adjust the length of the HR strap to fit
your chest size (under bust). Fastening the strap too tightly may cause discomfort.
* Wear the heart rate sensor so that the top of the sensor faces up.
* Ensure that the electrode pad is in direct contact with the
body.
* When your skin is dry, or wearing the heart rate sensor on
top of your undershirt may produce measurement errors.
To avoid errors, moisten the electrode pad.
Watch video
(YouTube)
Click the button, then a browser will open and a
video will be played back.
2
Temporarily secure the magnet
1
Temporarily secure the cadence magnet inside the crank
with nylon ties, so that it faces the sensor zone on the
CADENCE side.
2
Turn the sensor arm, and temporarily secure the wheel
magnet to the spoke that faces the sensor zone on the
SPEED side.
* When the speed sensor is not positioned appropriately in respect
to the two magnets (of
CADENCE
and
SPEED
), move the speed
sensor back and forth so that it is positioned properly. After you
move the speed sensor, adjust the position so that the two mag-
nets face the relevant sensor zone.
3
Adjust the distance to the magnet
1
Tilt the speed sensor so that the distance be-
tween the cadence magnet and the CADENCE
side of the speed sensor is about 3 mm, and
firmly secure it with the nylon ties.
2
Turn and adjust the sensor arm so that the
distance between the wheel magnet and the
sensor arm is about 3 mm, and firmly tighten
the sensor screw.
4
Securing various parts
Firmly tighten the nylon ties, sensor screw and magnet of
the speed sensor, and check for any loosening.
* For steel axle pedals, the cadence magnet can be magneti-
cally secured on the pedal axle. Make sure to remove the
double-sided tape from the magnet when doing this.
3 mm
(1/8”)
3 mm
(1/8”)
3 mm (1/8”)
Cadence
magnet
Speed sensor
CADENCE side
Wheel magnet
Heart rate sensor
HR strap
Hook
Back
Electrode pad
Cut extra length of the
nylon tie with scissors.
Sensor arm
SPEED side
Sensor
screw
Cadence
magnet
Wheel magnet
Sensor zone
Nylon ties
… 45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-GL51 Stealth evo plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-GL51 Stealth evo plus in the language / languages: English as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cateye CC-GL51 Stealth evo plus

Cateye CC-GL51 Stealth evo plus User Manual - German - 47 pages

Cateye CC-GL51 Stealth evo plus User Manual - Dutch - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info