This unit is a sensor-less cyclocomputer using GPS. An environment where a GPS signal can be received is required for measurement.
Three screens of GPS search screen, measurement screen, and standby screen are available in this unit, which are displayed alternatively according to the GPS receiving status and the bicycle
operating status. This section describes the flow of the screen after the power is turned on until measurement is started.
GPS search screen (when the power is turned on)
When the power is turned on, the GPS search screen will appear, and the GPS signal non-
receiving icon (
) will flash. Once GPS signal is received, the GPS signal receiving icon ()
will light up, and the display will change to the measurement screen.
* In an environment, including indoor, where GPS signal cannot be received, press the
MODE button to change to the measurement screen while the GPS signal non-receiving
icon () is still flashing.
* This unit starts searching GPS after the power is turned on. It may take several minutes to
acquire GPS signal depending on the receiving status.
Measurement screen
This is the basic screen of this unit. This screen is used during measurement.
Your can start/stop measurement and view the data under measurement.
According to the GPS signal receiving status, the computer operates in a different way as follows.
* For the functions available on the measurement screen, see “Functions available on the
measurement screen” (page 9).
When the GPS signal receiving icon ()
lights up
When the GPS signal non-receiving icon
() flashes
Measurement is enabled, and the unit
starts/stops measurement in sync with the
bicycle motion.
The speed unit flashes during measure-
ment.
* If GPS signal cannot be received while
riding, the GPS signal non-receiving
icon
(
) will flash, and the unit will
stop
measurement.
In such status, measurement is disabled
even while riding; however, only viewing the
measurement data and the resetting opera-
tion are enabled.
* Once GPS signal is received, the GPS
signal receiving icon (
) will light up,
and measurement will be enabled.
* The unit turns off the power automatically
in 10 minutes without pressing any button
in such status. (Auto power off)
GPS signal may not be received, thus the unit may stop measurement or may not display
appropriate measurements in the following locations or environments.
•In a tunnel, underground and building, between high-rise buildings, under an elevated
structure and arcade, etc.
•In bad weather (snow, rain, etc.)
•Near a high-voltage line or a mobile telephone relay station.
•When the computer display does not face to the sky.
Standby screen
The unit changes to the standby screen automatically in 10 minutes without any bicycle motion or
button operation, while the GPS signal receiving icon (
) flashes on the measurement screen.
Riding again returns to the measurement screen.
* The unit turns off the power automatically in 50 minutes with the standby screen dis-
played. (Auto power off)
* When the GPS signal cannot be received with the standby screen displayed, the GPS sig-
nal non-receiving icon (
) flashes. In such a case, the computer does not return to the
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Cateye CC-GL10 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Cateye CC-GL10 in the language / languages: English as an attachment in your email.
The manual is 3,02 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
