471846
11
Zoom out
Zoom in
Previous page
1/36
Next page
ENG
FR
11
RESTART
For formatting
Pour le formatage
For restarting
Pour relancer
4. Selecting speed unit
4. Choix de l'unité de vitesse
Ready
Prêt
Pressing the reset button for
five seconds
Appuyer sur le bouton RESET
pendant cinq secondes
3. Contrôle d'identification de la cadence capteur
Dans un délai de cinq minutes après le formatage ou l'opération de relance,
placez l'appareil principal près de la cadence capteur, et appuyez pour remettre
à l'état initial le bouton du capteur pendant cinq secondes. Le contrôle d'identi-
fication du capteur commence automatiquement, et l'écran suivant apparaît.
REMARQUE:
Vérifiez que la distance entre lunité principale et le capteur est dun mini-
mum de 20 cm afin dempêcher une mauvaise réception de signaux diden-
tification. Ajustez la distance et réinitialisez le capteur. Si la lettre E appa-
raît dans lAffichage-2, remplacez la pile du capteur selon les instructions
en page 33. Répétez ensuite la procédure de formatage (démarrage).
* Durant l'opération de formatage, le contrôle d'identification est suivi Sélectlon
de l'unité de mesure. Pendant l'opération de relance, le contrôle d'identification
est suivi du procédé final d'installation.Réglez ensuite lhorloge. (Voir la page 23.)
3. Checking the cadence sensor ID
Within five minutes after the formatting or the restarting operation, place the
main unit near the cadence sensor and press the reset button of the sensor for
five seconds. The checking of the sensor ID starts automatically, and the next
screen appears.
NOTE: The minimum transmission of the sensor is 20cm. The signal will be
too strong to perform the sensor ID check within 20cm of the main unit.
If the letter E appears in Display-2, replace the battery of the sensor
according to the description on page 33. After this, repeat the format-
ting operation (restarting operation).
* In the formatting operation, the ID checking is followed, Selecting the speed
unit.
In the restarting operation, the ID checking is the final set-up procedure. After
this, set the clock.(See page 23.)
Restarting operation
Press the RESTART button.
Appuyez sur le bouton de RESTART.
All items displayed (for 1 sec.)
Tous les éléments affichent (pendant 1 sec.)
Restarting is required when a battery is replaced, or when the computer
does not operate correctly. The following data will not be reset when restart-
ing: tire circumference setting; total distance; total time. Resetting clock time
is reguired.
Relancer est exigé quand une batterie est remplacée, ou lorsque l'ordinateur ne fonc-
tionne pas correctement. Les données suivantes ne seront pas remises à l'état initial
en relançant : configuration de circonférence de pneu ; distance totale; temps total.
In both operations, the sensor ID must be checked and the time must be re-set.
The next screen after formatting or restarting will be the sensor ID check screen.
Move to the next screen, Checking the cadence sensor ID.
Pendant les deux opérations, l'identification du capteur doit être contrôlée et
l'heure doit être remise à l'état initial. Avancez à l’écran suivant, Contrôle du
numéro didentification du capteur de cadence.
Relancer l'opération
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-CD300DW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-CD300DW in the language / languages: English, French as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cateye CC-CD300DW

Cateye CC-CD300DW User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info