646181

Caterchef 309.005 - U1 Manual

22
Zoom out
Zoom in
Previous page
1/44
Next page
- 22 -
ENGLISH
Connecting the water supply
Warning
1. The water connections must comply with local safety standards and regulations.
2. The minimum water pressure required is 2 kg/cm
2
. Cleaning performance will be adversely affected if water
pressure is too low.
The temperature of incoming water must not exceed 65°C, and water pressure must not exceed 5 kg/cm
2
.
Connect the inlet hose to the mains water supply (3/4” internal screw thread). Ensure that your hands are completely
clean before you connect the tap or magnetic valve to the mains water supply. The manufacturers will not accept any
responsibility for any damage or loss incurred as a result of foreign objects (e.g. dirt, iron or calcium) entering the tap
or the magnetic valve. Pull carefully on the inlet pipe to ensure that it is fi rmly attached. Open the tap slowly and
check that no water is leaking. It is necessary to fi rst check that the inlet pipe is fi rmly attached and the supply line is
open each time the dishwasher is used.
Water inlet (Requirements for water inlet)
Temperature Pressure (dynamic)
°C °F K Pa kg/cm
2
With 3 KW (230 V) electric boiler 40 ~ 60 104 ~ 140 196 ~ 490 2 ~ 5
With 6 KW (400 V) electric boiler 10 ~ 60 50 ~ 140 196 ~ 490 2 ~ 5
Water discharge
Connect the water discharge hose to a suitable drainage point. This must be lower that the discharge outlet of the
machine to ensure natural drainage. If necessary, to achieve this, the machine can be raised or placed on the
stainless steel support frame (optional), or the fi tter can install a drain pump (optional).
If local regulations require a grease trap, it must be installed by a certifi ed company.
Note: After installation, test the pressure of the incoming water supply. If the hydrodynamic pressure is lower than
2 kg/cm
2
, it will be necessary to install a pressure raising pump (from an independent supplier). If the stagnation
pressure is higher than 5 kg/cm
2
, it will be necessary to install a pressure reduction valve (from an independent
supplier)
Tests
Water inlet hose
Clean the water inlet hose before connecting it. Clean all fi lters after their fi rst use.
Water connection and hydrodynamic pressure
Check that the inlet hose is fi rmly connected. The hose may come loose and start leaking if the dishwasher is moved.
If the hydrodynamic pressure is too low, this may lead to malfunction of the machine.
Electrical connection
Connect up all the wires in the switch box (400V). Check that all wires are fi rmly connected. Check that the other
electrical components, for example the switches and cable, appear to be in good order.
Inspect the inside of the dishwasher
Check that there is nothing inside the machine that does not belong there (for example: clothes, screws, nuts & bolts,
tools, packaging materials, etc.).
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caterchef 309.005 - U1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caterchef 309.005 - U1 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info