Manual Cata IT 773 (page 21 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian)

740827

Zoom out

Zoom in

1/88

Protection against unintended switching-ON

· If the electronic control realizes a continuous operation of keys

for approx. 10 seconds, it switches OFF automatically. The

control sends out an audible failure signal for 10 seconds, so

that the user can remove the object which has been mistakenly

placed onto the operation surface. The displays show the

failure code “ E R 0 3 “ . If the failure carries on for more than

10 seconds, only the code “E R 0 3 “ will be displayed as long

as the failure will be recognized by the electronic control. If

the cooking zone is in the “hot” status, “H“ will appear on the

display in alteration with the failure notice.

· If no cooking zone will be activated within 20 seconds after

switching-ON by means of the Power-key, the control switches

back from the ON-condition into the stand-by-mode.

· When the control is switched- ON the ON/OFF-key has priority

over all other keys, so that the control can be switched-OFF

anytime, even in case of multiple or continuous operation of

keys.

· In the stand-by mode a continous operation will not be

signalized. However, before the electronic control can be

switched-ON again, it has to recognize that all keys are not

operated.

Key lock (child safety feature)

◊ Child safety feature:

Key lock:

After switching-ON the control the child safety feature can be

activated. To achieve this it is necessary to simultaneously

operate the front right cooking zone- select-key and the

MINUS-key and then press the front right cooking-zone-select

key again. There will be an “L”, meaning LOCKED (child safety

feature against unintended switching-ON). If a cooking zone is in

the “hot” condition, “L” and “H” will be displayed in alternation.

This course of operation has to take place within a period

of 10 seconds, no other key than described above may be

operated. Otherwise the input will be interrupted because of

incompleteness, the cook top will not be locked then.

The electronic control remains in a locked condition until it gets

unlocked, even if the control has been switched-OFF and -ON in

the meantime. Also a reset of the control (after a voltage drop)

does not cancel the key lock.

Unlocking for cooking purposes: :

To unlock and operate the control it is required to operate

the front right cooking- zone select- key and the MINUS-key

simultaneously. “L“ (LOCKED) in the display extinguishes and all

cooking zones show “0“ with a blinking dot. Should a cooking

zone be “hot”, “H” is displayed instead of the static “0”. After

switching- OFF the control, the child safety feature is active again.

Cancelling the key lock:

After switching-ON the control the child safety feature can be

deactivated. Here it is necessary to simultaneously operate the

front right cooking-zone-select key and the MINUS-key and then

operate the MINUS-key alone. If all steps have been carried out

in the right order within 10 seconds the key lock gets cancelled

and the control is OFF. Otherwise the input will be considered

incomplete, the control remains locked and switches-OFF after

20 seconds.

After a renewed switching-ON by means of the ON/OFF key all

displays show „0“, the display dots are blinking and the control

is ready for cooking. If a cooking zone is in “hot” mode, “0” and

“H” will be alternately displayed.

Audible signal (buzzer)

While the control is in operation the following activities will be

signaled by means of a buzzer:

· normal key activation with a short sound signal.

· continuous operation of keys over a longer period of time

(_10 seconds ) with a longer, intermittent sound signal.

Timer function (optional)

The timer function is realized in two versions:

· Stand-alone timer 1..99 min: sound signal when the time is

over (= minute minder). This function is only available when

the cooktop is not in operation, i.e. when there is no cooking.

· Cooking zone timer 1..99 min: sound signal when the time is

over, four cooking zones can be programmed independently.

Timer as minute minder (stand-alone):

· If the control is ON and no cooking zone selected, the

standalone-timer can be used by simultaneously operating

MINUS (2) and PLUS (3) keys.

· Adjustment range (0-99min), it can be set in 1-minute steps

with any key, starting at 1 up to 99 (end stop) with the minus-

key starting at 99 down to 0 (end stop)

· Continuous activation of the plusor minus-key results in a

dynamic increase of the adjustment speed up to maximum

value without sound signal.

· when the plus- or minus key is released in the meantime, the

adjustment speed starts again from a (low) initial value.

· adjustment can be made with a continously activated plus- or

minus-key or by tip-operation (with sound signal) After the

timer is set the time runs down according to the adjustment.

When the time is over there is a sound signal and the timer

display blinks.

The sound signal will be stopped

· automatically after 2 minutes and/or

· by operating any key.

Then the blinking of the timer display stops and the display

extinguishes.

Switching-OFF/changing the timer

· The timer can be changed or switched-off anytime by

simultaneously operating MINUS (2) and PLUS (3) keys. (with

sound signal). The timer will be switched off by counting down

to “0” with the minus-key.

For 6 seconds the timer display remains at “0“ before it will be

switched-off.

· If the control will be switched- ON by means of the Power-key,

the stand-alone timer will be switched-off also.

Timer programming on cooking zones

When the control is switched- ON an independent timer can be

programmed for every cooking zone.

· By selecting a cooking zone with the cooking-zone-selectkey (4),

then selecting the setting and, nally, operating MINUS (2) and

PLUS (3) keys simultaneously, the timer can be programmed

as a switch-off function for a cooking zone.

· During timer programming, the pilot light (6) of the selected

cooking zone blinks.

· When the timer has run down, there is a sound signal and

the timer display shows “00“ statically, the assigned cooking

zone timer LED blinks. The programmed cooking zone will

be cut off and „H“ will be displayed if the coking zone is hot,

otherwise a stroke will show in the cooking zone display.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cata IT 773 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cata IT 773 Manual

Product: