723255
28
Zoom out
Zoom in
Previous page
1/102
Next page
28
Image Adjustment 2 3
Overscan (CVD)
Adjust the overscan amount for an input video signal within the range of 0% to 5%*.
The size of the border area displayed on the projection screen depends on the
setting value. A smaller value results in a wider border area as shown below.
Image Adjustment 2 3
Restore Menu Defaults
(RCVD)
Return all of the items in the “Image Adjustment 2” main menu to their initial defaults
for the currently projecting image source.
Volume Adjustment 3
Volume
See “Adjusting the Volume Level (VOLUME)” (page 20) for more information.
Volume Adjustment 3
Restore Menu Defaults
Return the Volume setting to its initial default for the currently projecting image
source.
Screen Settings 3
Keystone Correction
Use this sub-menu to perform vertical keystone correction of the projected image.
Screen Settings 3
Aspect Ratio (RCVHD)
Select an aspect ratio setting for the projected image.
See “To change the aspect ratio of the projected image (ASPECT)” (page 17) for
more information.
Screen Settings 3
Projection Mode
Specify whether projection will be from the front of the screen or the back of the
screen.
Front*: Select this option to project from the front of the screen.
Rear: Select this option to project from the back of the screen. This setting flips the
front projected image horizontally.
Screen Settings 3
Ceiling Mount
Set up the projector to be positioned upside down for hanging from a ceiling.
On: Select when the projector is positioned upside down for hanging from a ceiling.
Since the bottom of the projector is upwards, the projected image is flipped
both horizontally and vertically.
Off*: Select when the projector is used on a desktop. This projects the image
assuming that the top of the projector is upwards.
Screen Settings 3
No Signal Screen
Select one of the following as the projection image whenever there is no input signal
being input to the projector: “Blue”* (blue screen), “Black” (black screen), “Logo”
(projector built-in logo, or user logo, page 76).
Screen Settings 3
Blank Screen
Select one of the following as the projection image whenever the [BLANK] key is
pressed: “Blue”* (blue screen), “Black” (black screen), “Logo” (projector built-in
logo, or user logo, page 76).
Screen Settings 3
Restore Menu Defaults
Return all of the items in the “Screen Settings” main menu to their initial defaults for
the currently projecting image source.
Input Settings 3
COMPUTER Terminal (RC)
Specify the method to be used to identify the COMPUTER terminal input signal.
Auto*: Projector automatically identifies the COMPUTER terminal input signal.
RGB: Always assumes the COMPUTER terminal input signal is an RGB signal.
Component: Always assumes the COMPUTER terminal input signal is a component
video signal.
Input Settings 3
RGB Level Adjust (RC)
Specifies whether level adjustment of the input RGB signal is enabled (On*) or
disabled (Off). Leaving this setting “On” will normally optimize the projected image.
However, depending on the input signal, there may be cases when this setting does
not optimize the image and may even distort it. If this happens, change this setting to
“Off”.
Use this menu item: To do this:
Display range at 5%
Display range at 0%
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio XJ-V10X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio XJ-V10X in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio XJ-V10X

Casio XJ-V10X User Manual - German - 102 pages

Casio XJ-V10X Quick start guide - German, Dutch - 22 pages

Casio XJ-V10X User Manual - Dutch - 102 pages

Casio XJ-V10X Quick start guide - Italian, Portuguese, Swedish - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info