543361
37
Zoom out
Zoom in
Previous page
1/47
Next page
37
System Admin > Setup Settings
System Admin Page Settings
Setting Name Description
IP Setup Obtain an IP
address
automatically/
Use the following IP
address
Specifies whether you want to obtain an IP address automatically or specify an IP
address manually.
z Selecting “Use the following IP address” applies IP address, subnet mask, and
default gateway information that you input manually.
z Specification of IP address, subnet mask, and default gateway information is
not necessary (and is not allowed) when you select “Obtain an IP address
automatically”.
Initial Default: Obtain an IP address automatically
IP Address Specifies the projector’s IP address.
Initial Default: 192.168.100.10
Subnet Mask Specifies a subnet mask value, which specifies the IP address range of the subnet
to which the projector belongs.
Initial Default: 255.255.255.0
Default Gateway Specifies the subnet default gateway.
Initial Default: 192.168.100.10
DHCP Setup Auto/Disable Specifies whether an IP address should be assigned automatically to a computer
connected to the projector via wireless LAN. “Auto” causes an IP address to be
assigned automatically, while “Disable” turns off auto assignment.
Initial Default: Auto
Starting IP Address Specifies the start point of the range of IP addresses that are assigned
automatically to computers. This setting is available only while “Auto” is selected
for the DHCP Auto/Disable setting.
Initial Default: 192.168.100.11
Ending IP Address Specifies the end point of the range of IP addresses that are assigned
automatically to computers. This setting is available only while “Auto” is selected
for the DHCP Auto/Disable setting.
Initial Default: 192.168.100.254
Wireless Setup SSID Wireless network ID name. This is normally referred to as the SSID, ESS-ID, or
network name. Up to 24 single-byte alphanumeric characters can be entered.
Initial Default: casiolpj_default1
SSID Broadcast Specifies whether SSID information broadcasting is enabled or disabled.
Initial Default: Enable
Channel Specifies the channel used for wireless LAN communication. Selecting “Auto”
causes auto selection of a channel that is appropriate for the current
communication environment. To specify a channel number, select channel number
1 through 11 from the list that appears when you click the [
T
] button to the right of
the channel number.
Initial Default: Auto
Security Specifies the security protocol. For more information, see “To configure security
settings” (page 21).
Initial Default: WPA-PSK AES
Passphrase/WEP
Key
Specifies the passphrase or WEP key in accordance with the security protocol
selected with “Security” above. For more information, see “To configure security
settings” (page 21).
IEEE 802.11n Specifies whether wireless LAN standard IEEE 802.11n is enabled.
Initial Default: Enable
Channel Width Specifies either “20MHz” or “Auto” for the IEEE 802.11n channel width.
Initial Default: 20MHz
Projector name Input up to 32 characters for a name to be used as the projector’s identity.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio XJ-ST145 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio XJ-ST145 in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio XJ-ST145

Casio XJ-ST145 Additional guide - English - 67 pages

Casio XJ-ST145 Quick start guide - English - 26 pages

Casio XJ-ST145 User Manual - English - 64 pages

Casio XJ-ST145 User Manual - German - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info