215492
37
Zoom out
Zoom in
Previous page
1/40
Next page
E-37
Troubleshooting
English
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red steady
:–
The projector was turned off automatically due to some
problem that was probably caused by external digital noise or
some other reason. Confirm that the POWER/STANDBY
indicator is lit red (without flashing) and that the fan has
stopped. After checking the POWER/STANDBY indicator,
disconnect the power cord from the projector and wait for all
of the projector’s indicators to go out. Next, reconnect the
power cord and turn projector power back on.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message : –
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(0.5-second interval)
: Red flashing
(0.5-second interval)
The projector was turned off automatically because the lamp
turned off or did not turn on. After confirming that the
POWER/STANDBY indicator is lit red (without flashing), unplug
the power cord. Wait for a short while and then plug it back
in and turn on the projector again.
If the error occurs again when you turn power back on, wait
until the projector cools down and then replace the lamp
(page E-29).
If the lamp does not light after you replace it, contact your
retailer or nearest authorized CASIO Service Center.
Message : –
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(2-second interval)
:–
Power has turned off automatically due to a projector memory
error. Confirm that the POWER/STANDBY indicator is lit red
(without flashing) and that the fan has stopped. After checking
the POWER/STANDBY indicator, disconnect the power cord
from the projector and wait for all of the projector’s indicators
to go out. Next, reconnect the power cord and turn projector
power back on.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message : –
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Amber flashing
(1-second interval)
:–
Power has turned off automatically because the lamp cover is
open. Perform the following steps.
1 After confirming that the POWER/STANDBY indicator is lit
red (without flashing), disconnect the power cord from the
projector.
2 Check to make sure that the lamp cover is closed.
3 Plug the power cord back in and turn the projector back
on again.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message : –
POWER
TEMP
LAMP
: Green steady
:–
: Red flashing
(1-second interval)
It is time to replace the lamp. Replace the lamp following the
steps under
Replacing the Lamp” (page E-29). Press the
[ESC] key to clear the warning message.
Message : It is time to replace
the lamp. Use the
procedure in the
User’s Guide to
replace the lamp as
soon as possible.
Indicator/Error Message Description and Required Action
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio xj s36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio xj s36 in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info