522439
71
Zoom out
Zoom in
Previous page
1/132
Next page
Using the Song Sequencer
E-69
4.
Use the R-17 (u, i) buttons to select a track
(Track 01 through Track 16).
5.
Configure panel settings as required for your
performance.
Configure the following settings: tone selection, tempo,
mixer settings, etc. For details about settings that can
be configured, see “Recording Start” under “System
Track and Track 01 through 16 Common Recording
Content” (page E-66) and “Track 01 through 16
Recording Content” (page E-66). For information about
mixer settings, see “Mixer Settings in the Song
Sequencer Mode” (page E-71).
6.
Perform the following steps to configure beat
and other settings.
7.
Start playing something on the keyboard.
This will start recording and cause the C-2 (RECORD)
button to change from flashing to lit. During recording,
the display will show the current measure (MEASURE)
and beat (BEAT).
To input one or more rests before starting recording,
press the L-16 (START/STOP) button to start
recording, and then start keyboard play at the point you
want.
PITCH BEND wheel (S-1) and pedal operations are
also recorded.
When recording reaches a point where there is less
than 100 notes of remaining memory capacity, the
current measure (MEASURE) and beat (BEAT) values
will start flashing.
8.
To stop recording, press the L-16 (START/
STOP) button.
At this time you can press the L-16 (START/STOP)
button to replay what you have just recorded. For
details about playing back recorded content, see
“Playing a Recorded Song” (page E-72).
9.
To exit the song sequencer, press the C-3
(SONG SEQUENCER) button or the R-15 (EXIT)
button.
(1) While holding down the R-13 (FUNCTION) button,
press the C-13 (MENU) button.
This will display a menu like the one shown below, with
the 0 next to “Beat” (beat).
(2) Use the dial or R-14 (–, +) buttons to configure the beat
setting.
You can specify a beat setting of 2/4 to 8/4, 2/8 to 16/8.
(3) Use the R-17 (y) button to move the 0 to
“Metronome” and then use the R-14 (–, +) buttons to
turn the metronome on or off.
Turning on the metronome causes it to count a count
during recording, but not during playback.
(4) Use the R-17 (y) button to move the 0 to “Precount”
and then use the R-14 (–, +) buttons to turn the
precount on or off.
Turing on the precount inserts a one-measure count
before the start of recording when you press the L-16
(START/STOP) button in step 7.
(5) Use the R-17 (y) button to move the 0 to “RecType”,
and then use the R-14 (–, +) buttons to select “REPL”
or “OVDB”.
When you want to perform this type
of recording:
Select this
RecType option:
Delete any data currently existing in
the track being recorded to and start a
new recording.
REPL (Replace)
Overdub any data currently existing in
the track being recorded to with the
new recording.
OVDB (Overdub)
(6) Press the R-15 (EXIT) button to exit the menu.
CTK6200_e.book 69 ページ 2011年12月27日 火曜日 午後8時20分
71


Need help? Post your question in this forum.

Forumrules
1

Forum

casio-wk-6600

Reset search

  • how do you control track volumes in auto accompinament Submitted on 3-5-2023 at 12:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio WK-6600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio WK-6600 in the language / languages: English as an attachment in your email.

The manual is 8,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio WK-6600

Casio WK-6600 User Manual - German - 131 pages

Casio WK-6600 User Manual - Dutch - 131 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info