Manual Casio KL8200 (page 29 of 36) (English)

506039

Zoom out

Zoom in

1/36

E-28

• If you do not want to receive and append any more data

items, skip steps 4 and 5.

5. Repeat step 3 to receive more data.

• The “!” indicator means that data items will be printed

one at a time. If you want to print all of the received data

items at once, press B to change “!” to “A”. Press B

again to change back to “!”.

6. Press PRINT to print the data.

• If “!” is on the display, pressing PRINT prints the single

data item where the cursor is currently located. Use u

and i to move the cursor to the data item you want to

print.

• If “A” is on the display, pressing PRINT prints all of the

received data items.

• Use a tape that is at least 9mm wide when printing re-

ceived data items.

• You can enlarge received data item character size verti-

cally by a factor of two and horizontally up to a factor of 4.

• Use a tape width of at least 18mm when received data

item character size is increased vertically by a factor of

two.

• None of the following functions can be used with received

data: frames, preset formats, auto sizing, preset layouts,

block operations, proportional character spacing, smooth-

ing, character input settings, character deletion, text stor-

age into memory, text recall from memory.

• The printer returns to the screen in step 3 (the one that

appears after data communication is complete) after print-

ing is complete.

7. Press ESC SET to quit data communications.

• All received data is cleared from label printer memory when

you quit data communications.

8. Turn the label printer and Copy Pen off and disconnect

the cable.

Importing Data from a Graphic Scientific

Calculator

Use the following procedure to send data to the label printer

from one of the following CASIO Graphic Scientific Calcula-

tor models: CFX-9800G, RM-9800G, fx-7700GH, fx-

9700GH, CFX-9850G, CFX-9950G.

Important!

• Note that some of the steps you need to perform in the

following procedure depend on the graphic scientific cal-

culator model you are sending data from.

• Before performing any of the procedures in this section,

make sure that the width of the tape loaded in your label

printer is 9mm or greater.

To connect the graphic scientific calculator to

the label printer

1. Turn off the power of the label printer and the calculator.

2. Use the optionally available SB-62 Connecting Cable to

connect the calculator to the label printer.

• You have to remove the connector cover of the graphic

scientific calculator to attach the cable. Keep the connec-

tor cover in a safe place so you can replace it later.

3. Turn on the calculator and then the label printer.

To send data from a graphic scientific

calculator to the label printer

1. Set up the calculator to send data.

• CFX-9850G, CFX-9950G

In the data communication main menu, press F6 (IMGE),

and then select “Monochrome” for Image Set.

F2 (MONO)

Next, display the screen you want to send.

• fx-7700GH, fx-9700GH

Display the setup screen and specify COPY as the func-

tion of the M-Disp key.

Next, display the screen you want to send.

• CFX-9800G, RM-9800G

Display the setup screen and press F3 (MON) to specify

MONOCHR as the function of the M-Disp key.

Next, display the screen you want to send.

2. On the label printer, press FUNC, DEL (COMM) and then

SET to set it up to receive data.

• The above operation causes the message “RECEIVE OK!”

to appear on the label printer’s screen to indicate that it is

standing by to receive data. If you do not perform the next

step within 20 seconds after this message appears, the

message changes to “SEND ERROR!” If this happens,

press ESC and start again.

3. Start the data send operation on the calculator.

• CFX-9850G, CFX-9950G

Press [F<>D].

• fx-7700GH, fx-9700GH, CFX-9800G, RM-9800G

Press M-Disp.

4. After data communication is complete, the screen of the

label printer appears as shown below.

1ATAD

c9.41×1

• The received data is indicated on the display as “DATA 1”,

“DATA 2”, and so on. Up to 15 data items can be received,

as long as the total length of the tape to print the data

items does not exceed 250mm.

• If the message “SEND ERROR!” is on the screen, press

ESC and try again.

5. On the label printer, press CAPS to specify the receive

mode of additional data items.

Each press of CAPS toggles label printer between the

following two modes.

• COMM

Received data is appended to the end of previously

received data.

• COMM

Received data replaces previously received data.

• If you do not want to receive and append any more data

items, skip steps 5 and 6.

6. Press SET and repeat step 3 to receive more data.

• The “!” indicator means that data items will be printed

one at a time. If you want to print all of the received data

items at once, press B to change “!” to “A”. Press B

again to change back to “!”.

7. Press PRINT to print the data.

• If “!” is on the display, pressing PRINT prints the single

data item where the cursor is currently located. Use u

and i to move the cursor to the data item you want to

print.

• If “A” is on the display, pressing PRINT prints all of the

received data items.

• Use a tape that is at least 9mm wide when printing re-

ceived data items.

• You can enlarge received data item character size verti-

cally by a factor of two and horizontally up to a factor of 4.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio KL8200 in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio KL8200

Casio KL8200 User Manual - German - 39 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio KL8200 Manual

Product: