506041
26
Zoom out
Zoom in
Previous page
1/33
Next page
G-25
Texteingabe
Strichcode-Spezifikationen
*1 Die Prüfzahl wird automatisch in Übereinstimmung mit den Eingabedaten
festgelegt. Bei EAN-13 und EAN-8 wird die Anzahl der Stellen am Ende der
ausgedruckten Stellen angehängt.
*2 Die Anzahl der unter einem Strichcode ausgedruckten Stellen entspricht
den Eingabezeichen plus den automatisch angehängten Zeichen.
*3 Eine Fehlermeldung wird im Falle einer nicht ausreichenden Zahl von Stellen
angezeigt. Ebenso ist eine Eingabe nicht möglich, wenn die Anzahl der Stellen
überschritten wird.
Störungsbeseitigung
Stromversorgung
Strichcode-
Typ
EAN-13
EAN-8
Prüfzahl
*1
Ja
Ja
Automatisch
zugeordnete
Anzahl der Stellen
(Prüfzahl *1)
1
1
Eingabezeichen
Ziffern (0 ~ 9)
Ziffern (0 ~ 9)
Eingabe-
stellen *3
12
7
Batteriespannung zu
niedrig.
Inkorrekte Einstellung
des Display-Kontrasts.
Batterien inkorrekt
eingelegt.
Netzadapter inkorrekt
angeschlossen.
Die Batterien ersetzen.
Den Display-Kontrast einstellen.
Die Batterien herausnehmen und
wieder korrekt einlegen.
Sich vergewissern, daß der
Netzadapter korrekt angeschlossen ist.
Keine Anzeige am Display.
Mögliche Ursache Abhilfe Seite
G-6
G-23
G-7
G-7
FUNKTION-Taste wurde
gedrückt.
ESC drücken, um die FUNKTION-
Taste zurückzustellen.
Texteingabe nicht möglich.
Mögliche Ursache Abhilfe Seite
G-10
Abdeckung des
Etikettenband-Fachs nicht
korrekt geschlossen.
Kein Band in der
Kassette.
Bandstau.
Die Abdeckung fest schließen.
Die Etikettenband-Kassette durch ein
Neuteil ersetzen.
Die Etikettenband-Kassette entfernen,
dann das gestaute Band von Hand
herausziehen. Das überstehende
Band mit einer Schere abschneiden,
dann die Kassette wieder korrekt in
den Etikettendrucker einsetzen.
Wichtig!
Darauf achten, daß der Auslaßschlitz
nicht blockiert wird; niemals das sich
herausschiebende Band während
des Druckvorgangs berühren.
Band wird nach dem Drücken von DRUCK herausgeschoben,
doch das Band ist leer.
Mögliche Ursache Abhilfe Seite
Es wurden nur
Leerstellen eingegeben.
Den auszudruckenden Text
eingeben.
G-8
G-8
G-8
G-10
Band wird beim Drücken von DRUCK nicht herausgeschoben.
Mögliche Ursache Abhilfe Seite
Anzahl
der
Stellen *2
13
8
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio KL200E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio KL200E in the language / languages: German as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info