587024
22
Zoom out
Zoom in
Previous page
1/70
Next page
20
EN
4.
Press the arrow key.
5.
Specify a cut mode.
Cut modes are explained in the table below.
Select this mode: To do this:
CONT. HALF CUT
Print without cutting the backing paper
between labels.
FULL + HALF CUT Cut between labels.
FULL CUT Print on iron-on transfer tape.
UNCUT
Print on refl ective tape, magnetic tape or iron-
on fabric tape.
Here, we will specify CONT. HALF CUT.
6.
Press SET.
This starts printing.
The backlight will be unlit while printing is in progress.
To interrupt printing part way through, press ESC.
Affi xing a Label to a Surface
1.
If required, use scissors or some other implement to trim the label to the
desired size or shape.
2.
Peel off the backing of the label and affi x the
label to the desired surface.
Peeling off the backing of a half cut label
Carefully twist at the half cut point and then
peel the backing from the label.
Peeling off the backing of a full cut label
HAPPY!
PPY!
Bending a corner of the label makes the backing easier to peel off.
Removing a label from a surface where it was affi xed may cause
adhesive residue to remain on the surface.
Important!
Do not try to affi x a label to the objects or in the locations described below.
On a surface exposed to direct sunlight or rain
On the body of a person or animal
On a utility pole, on a fence or structure not owned by you, etc.
On a container used for heating in a microwave oven
Incompatible Surfaces
Rough or grainy surfaces
Wet, oily, dusty, or otherwise soiled surfaces
Special plastic (silicon, polypropylene, etc.) surfaces
Feeding Tape
You can perform a tape feed operation either before or after printing.
1.
Press FUNCTION and then .
This feeds the tape approximately 21mm (
13
/
16
").
Finalizing a Print Operation when NONE is
Selected for the Margin Setting
When NONE is specifi ed for the margin setting, the printer does not cut the
tape automatically at the end of a print operation. In this case, perform the
operation below to cut the tape.
1.
Press FUNCTION and then .
This cuts the tape.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio KL-G2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio KL-G2 in the language / languages: English as an attachment in your email.

The manual is 7,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio KL-G2

Casio KL-G2 User Manual - German - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info