641950
2
Zoom out
Zoom in
Previous page
1/3
Next page
Operation Guide 3229/3421
E-10
Mode indicator
Alarm on indicator
DayMonth
Minutes
Hour
Hourly time signal
on indicator
Alarm
You can set an alarm with hour, minutes, month, and
day. When the alarm is on, the alarm sounds for
20 seconds at the preset time. When the Hourly Time
Signal is on, the watch beeps every hour on the hour.
Alarm Types
The types of alarm you get depends on the information
you set.
To set a daily alarm
Set the hour and minutes for the alarm time. Set “
for the month and “– –” for the day (see step 3 under
“To set the alarm time”). This type of setting causes
the alarm to sound every day at the time you set.
To set a date alarm
Set the month, day, hour and minutes for the alarm
time. This type of setting causes the alarm to sound
at the specific time, on the specific date you set.
E-11
To set a 1-month alarm
Set the month, hour and minutes for the alarm time. Set “” for the day (see step
3 under To set the alarm time”). This type of setting causes the alarm to sound
every day at the time you set, only during the month you set.
To set a monthly alarm
Set the day, hour and minutes for the alarm time. Set “” for the month (see step 3
under “To set the alarm time”). This type of setting causes the alarm to sound every
month at the time you set, on the day you set.
To set the alarm time
1. Press A while in the Alarm Mode until the hour digits start to flash on the display.
The hour digits flash because they are
selected
.
At this time, the alarm is automatically switched on.
2. Press C to change the selection in the following sequence.
Hour
Day
Minutes
Month
E-12
3. Press B to increase the selected digits. Holding down B changes the number at
high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4. After you set the alarm time, press A to return to the Alarm Mode.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
E-13
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To switch an alarm and Hourly Time Signal on and off
Press B while in the Alarm Mode to change the status of an alarm (see “Alarm
Types” on page E-10) and Hourly Time Signal in the following sequence.
Both off Both onAlarm only Hourly Time Signal only
Hourly time signal on indicator
Alarm on indicator
E-14
Mode indicator
Minutes
SecondsHours
Current time
Countdown Timer
The countdown timer can be set within a range of 1
second to 24 hours. When the countdown reaches
zero, an alarm sounds for 10 seconds or until you press
any button.
To set the countdown time
1. Press A while in the Countdown Timer Mode. The
hours digit flashes on the display because it is
selected
.
2. Press C to change the selection in the following
sequence.
Seconds
Minutes
Hours
E-15
3. Press B to increase the selected number. Holding down B changes the number
at high speed.
To set the starting value of the countdown time to 24 hours, set 0:00' 00.
4. After you set the countdown time, press A to return to the Countdown Timer Mode.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Timer Mode automatically.
To use the countdown timer
1. Press B while in the Countdown Timer Mode to start the countdown timer.
2. Press B again to stop the countdown timer.
You can continue countdown timer operation by pressing B.
3. Stop the timer and then press A until the countdown time is reset to its starting
value.
When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button. Countdown
timing stops, and the countdown time is automatically reset to its starting value
after the alarm stops.
E-16
Auto repeat on indicator
1. Press A while in the Countdown Timer Mode. The
hours digit flashes on the display because it is
selected
.
2. Press D to switch auto repeat on and off.
3. Press A to return to the Countdown Timer Mode.
When the end of the countdown is reached while
auto repeat is on, the alarm sounds, but the
starting countdown time is reset and countdown
timing starts again automatically whenever the
countdown reaches zero. You can stop timing by
pressing B, and manually reset to the starting
countdown time by pressing A.
To switch auto repeat timing on and off
E-17
Current time
Mode indicator
Minutes
Seconds
1/100 second
The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes. The range of the
stopwatch is 23 hours, 59 minutes, 59 seconds.
To measure elapsed time
1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.
You can resume the measurement operation by
pressing B again.
3. Press A to clear the stopwatch to all zeros.
For the first 60 minutes, the display shows minutes,
seconds, and 1/100 second. After 60 minutes, the
display format changes to show hours, minutes, and
seconds.
Stopwatch
E-18
To record split times
1. Press B to start the stopwatch.
2. Press A to display the timing up to that point. Stopwatch timing continues internally.
3. Press A to clear the split time and to continue time measurement on the display.
You can repeat steps 2 and 3 as many times as you want.
4. Press B to stop the time measurement.
5. Press A to clear the stopwatch to all zeros.
To time first and second place finishes
1. Press B to start the stopwatch.
2. Press A when the first finisher crosses the line, and record the time.
3. Press B when the second finisher crosses the line.
4. Press A to display the finishing time of the second finisher.
5. Press A again to clear the stopwatch to all zeros.
E-19
Specifications
Accuracy at normal temperature: ±15 seconds a month
Timekeeping: Hour, minutes, seconds, pm (PM), month, day, the day of the week
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Auto-calendar pre-programmed from the year 2000 to 2099
Alarm: Multi-function alarm, hourly time signal
Countdown Timer
Measuring unit: 1 second
Input range: from 1 second to 24 hours
Other: Auto-repeat function
Stopwatch
Measuring units: 1/100 second (for the first 60 minutes)
1 second (after 60 minutes)
Measuring capacity: 23 hours, 59 minutes, 59 seconds
Measuring modes: Elapsed time, split time and two finishes
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio DW5600E G-Shock - 3229 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio DW5600E G-Shock - 3229 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio DW5600E G-Shock - 3229

Casio DW5600E G-Shock - 3229 User Manual - German - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info