624853
24
Zoom out
Zoom in
Previous page
1/26
Next page
Troubleshooting
Auto time setting is not
correct.
Q1
The watch cannot perform a receive
operation.
Is the watch’s battery charged?
Signal reception is not possible while
battery power is low. Keep the watch
exposed to light until it recharges
sufficiently.
l
Solar Charging
Is the watch in the Timekeeping Mode?
Time signal auto receive is performed only
while the watch is in the Timekeeping
Mode.
Press (B) to enter the Timekeeping
Mode.
To trigger a time signal receive
operation manually, enter the Receive
Mode
and then hold down the (A) button
for about two seconds.
l
Navigating Between Modes
l
Auto Time Adjustment
Is your Home City setting correct for your
location?
The watch will not indicate the correct time
if
the Home City setting is wrong. Change
your Home City setting so it correctly
reflects your location.
l
Setting a Home Time City
After checking the above, the watch still
cannot perform a receive operation.
Time signal reception is not possible
when any one of the conditions exists.
When watch is at Level 2 power saving
Barometric Pressure Change
Indications turned on
Timer countdown in progress
If successful reception is not possible for
some
reason, you can adjust the time and
day settings manually.
Q2
The signal receive operation always
fails.
Is the watch in a location that is appropriate
for signal reception?
Check your surroundings and move the
watch
to a location where signal reception
is better.
l
Appropriate Signal Reception Location
Did you avoid touching the watch while the
receive operation was in progress?
Minimize movement of the watch and do
not perform any watch operation while a
receive operation is in progress.
Is there an alarm configured to sound
during the same period that the signal
receive operation is performed?
Receive stops if an alarm operation starts
while it is being performed. Disable the
alarm.
l
Turning an Alarm On or Off
Is the signal transmitter in your area
transmitting a signal?
The transmitter of the time signal may not
be transmitting. Try again later.
Q3
Time setting is incorrect even when
time signal reception is successful.
Strong magnetism or impact may cause the
hands of the watch to go out of alignment.
Adjust hand alignment.
l
Adjusting Hand Alignment
Altitude Measurement
Q1
Readings
produce different results at
the same location.
Watch readings are different from
altitude information available from
other sources.
Correct altitude readings are not
possible.
Relative altitude is calculated based on
changes
in barometric pressure measured by
the watch’s pressure sensor. This means that
barometric pressure changes can cause
readings taken at the same location to be
different. Also note that the value displayed by
the watch may be different from the actual
elevation and/or sea level elevation indicated
for the area where you are located. When
using the watch’s altimeter while mountain
climbing, it is recommended that you regularly
calibrate its readings in accordance with local
altitude (elevation) indications.
l
Calibrating Altitude Readings
Q2
Following a relative altitude reading,
the watch’s second hand points to 9
o’clock.
The second hand will move to 9 o’clock if a
reading is outside the allowable altitude
measurement range (-700 m to 10,000 m
(-2,300
to 32,800 feet)). If [ERR] is displayed,
there may be a problem with the sensor.
l
Taking a Relative Altitude Reading from
Some Reference Point
Q3
[ERR]
appears during measurement.
There may be a problem with the sensor. Try
taking another measurement. If [ERR] keeps
appearing after multiple measurement
attempts, contact a CASIO service center.
Operation Guide 5470
24
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5470 - PRW-6100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5470 - PRW-6100 in the language / languages: English as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5470 - PRW-6100

Casio 5470 - PRW-6100 User Manual - German - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info