624486

Casio 5443 Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
E-56
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
D
to select the Countdown Timer Mode as shown on page E-8.
• The mode dial hand will move to
TMR
and the display will show the current countdown time.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
down), press
E
to stop it and then press
A
to reset to the current
countdown start time.
• If a countdown is paused, press
A
to reset to the current
countdown start time.
2. Hold down
A
until the minute setting of the current countdown start
time starts to fl ash. This is the setting screen.
3. Use
E
(+) and
B
(–) to change the minute.
• You can set a countdown start time from 1 to 60 minutes, in one-
minute increments.
• Holding down
E
or
B
scrolls the minutes at high speed.
4. Press
A
to exit the setting screen.
Countdown time
(Minutes, seconds)
Countdown time
(Minutes, seconds)
E-57
To perform a countdown timer operation
E
E
E E
A
Start Stop (Resume) (Stop) Reset
• Before starting a countdown timer operation, check to make sure that a countdown operation is not
already in progress (indicated by the seconds counting down). If it is, press
E
to stop it and then
A
to reset to the countdown start time.
• An alarm sounds for 10 seconds when the end of the countdown is reached. This alarm will sound in all
modes. The countdown time is reset to its starting value automatically after the alarm sounds.
To stop the alarm
Press any button.
E-58
Using the Alarm
You can set fi ve independent daily alarms.
When an alarm is turned on, an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the watch is not in the Timekeeping
Mode.
You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the
hour.
To enter the Alarm Mode
Use
D
to select the Alarm Mode as shown on page E-9.
• The mode dial hand will move to
ALM
.
• The display will initially show the currently selected alarm number
indicator (
AL1
to
AL5
) or the hourly time signal indicator (
SIG
). Next,
the indicator will alternate with the alarm time setting (in the case of an
alarm) or
:00
(in the case of the hourly time signal).
Alarm time
(Hour : Minutes)
Alarm number or SIG
Alarm time
(Hour : Minutes)
Alarm number or SIG
E-59
To set an alarm time
1. In the Alarm Mode, use
E
to scroll through the alarm screens on the display until the one you want to
change is shown.
AL1 AL2 AL3
SIG AL5 AL4
2. Hold down
A
until the hour digits of the alarm setting start to fl ash on the display.
• This is the setting screen.
3. Press
D
to move the fl ashing between the hour and minute settings.
4. While a setting is fl ashing, use
E
(+) and
B
(–) to change it.
• Holding down
E
or
B
scrolls settings at high speed.
• When setting the alarm time using the 12-hour format, take care to
set the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press
A
to exit the setting screen.
To test the alarm
In the Alarm Mode, hold down
E
to sound the alarm.
E-60
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
E
to select an alarm or the Hourly Time
Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press
A
to turn it on
(
on
)
and off
(- -)
.
•
The alarm on indicator (when any alarm is on), and the Hourly Time
Signal on indicator (when the Hourly Time Signal is on) are shown on
the display in all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Alarm on indicator
Hourly time signal
on indicator
Alarm on indicator
E-61
Illumination
The display of the watch is illuminated for easy reading in the dark. The watch’s auto light switch turns on
illumination automatically when you angle the watch towards your face.
• Auto light must be enabled (page E-63) for it to operate.
To illuminate the display manually
Press
B
in any mode (except when a fl ashing setting screen is
displayed) to illuminate the display.
• You can use the procedure below to select either 1.5 seconds or 3
seconds as the illumination duration. When you press
B
, the display
will remain illuminated for about 1.5 seconds or 3 seconds, depending
on the current illumination duration setting.
• The above operation illuminates the display regardless of whether auto
light is enabled or disabled.
To change the illumination duration
1. In the Timekeeping Mode, hold down
A
until
ADJ
appears on the display.
• When you release
A
(after ADJ appears), the second hand will be pointing at the currently
selected city code.
2. Use
D
to cycle through the settings on the display until the current illumination duration (
LT1
or
LT3
) is
shown.
• See the sequence in step 2 of the procedure under “To change the current time and date
settings” (page E-17) for information about how to scroll through setting screens.
E-62
3. Press
E
to toggle the illumination duration between three seconds (
LT3
displayed) and 1.5 seconds
(
LT1
displayed).
4. After all of the settings are the way you want, press
A
to exit the setting screen.
About auto light
While auto light is enabled, illumination will turn on whenever you
position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and
then tilting it towards you more than 40 degrees causes
illumination to turn on.
Warning!
•
Always make sure you are in a safe place whenever you are reading the display of the watch
using auto light. Be especially careful when running or engaged in any other activity that can
result in accident or injury. Also take care that sudden illumination by auto light does not startle
or distract others around you.
•
When you are wearing the watch, make sure that auto light is disabled before riding on a bicycle
or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of auto
light can create a distraction, which can result in a traffi c accident and serious personal injury.
More than
40°
Wear the watch on the
outside of your wrist
More than
40°
Wear the watch on the
outside of your wrist
E-63
Note
• Auto light is always disabled, regardless of its enabled/disabled setting, when any one of the following
conditions exists.
While an alarm is sounding
While the watch is in the Digital Compass Mode
While a hand shift operation is in progress
• If you have auto light enabled, display illumination may be delayed if you angle the watch towards your
face while a temperature reading operation is being performed.
To enable or disable auto light
In the Timekeeping Mode, hold down
B
for about three seconds to
toggle auto light between enabled (
LT
shown on the display) and
disabled (
LT
not displayed).
• The auto light enabled indicator (
LT
) is on the display in all modes
while auto light is enabled.
• The auto light switch remains enabled for about six hours. After that it
becomes disabled automatically.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light enabled
indicator
Auto light enabled
indicator
Operation Guide 5442 5443
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5443 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5443

Casio 5443 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info