586703

Casio 5425 Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
Operation Guide 5146 5425
E-20
Lap Time
A lap time reading shows the time elapsed since the last
lap time reading was taken.
•
If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting (page E-15).
•
If you want the watch to calculate the speed of the
entire race, specify the race distance for the distance
setting (page E-15). A speed will be indicated each
time you take a lap reading, but these lap speeds will
not indicate actual speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press $.
2. Make sure that LAP (lap times) is shown in the lower digital display.
• If SPL (split times) is displayed, press
$
to toggle it to LAP.
Lap time
E-21
To perform a lap time measurement
Select lap time (LAP) measurement and then perform the
following button operations.
'
Start
➝ $
Lap*
➝ $
Lap*
➝
'
Stop
➝ $
Reset
* Normal elapsed time measurement reappears after
about 12 seconds.
• You can press
$
to take lap readings as many times
as you like.
• While a lap time is displayed, the upper digital display
will alternate between the lap number (
#01
to
#99
) and
the lap hour value. If you take more than 99 lap
readings, the lap number will restart from
#00
following
lap
#99
.
• Pressing
'
to stop elapsed time measurement
displays the time (and speed if a distance is specifi ed)
of the fi nal lap.
Lap number
Speed hand
(calculated)
Minutes
Seconds
1/1000
second
s
Hours
E-22
Split Time
A split time reading shows the time elapsed since the
beginning of the current time measurement.
• If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting (page
E-15).
• For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based
on the total race distance, and so they will not indicate
actual intermediate split speeds.
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press $.
2. Make sure that SPL (split times) is shown in the lower digital display.
• If LAP (lap times) is displayed, press
$
to toggle it to SPL.
Split time
E-23
To perform a split time measurement
Select split time (SPL) measurement and then perform the
following button operations.
'
Start
➝ $
Split
➝ $
Split Release*
➝
'
Stop
➝ $
Reset
* The split time is released automatically if you do not
press
$
within about 12 seconds.
• You can press
$
to take split readings as many times
as you like.
• The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
• Pressing
$
while a split time is displayed will switch
back to normal elapsed time measurement. The
elapsed time will appear in the lower digital display.
• You also could press
'
to stop elapsed time
measurement instead.
• Pressing
'
to stop elapsed time measurement
displays the time (and speed if a distance is specifi ed)
of the fi nal split (which is the overall elapsed time).
Hours
1/1000
second
s
Minutes
Seconds
Speed hand (calculated)
E-24
To measure times with the stopwatch
Elapsed Time
D
D A
Start Stop Reset
Lap Time
D
A A D A
Start
(
LAP
displayed)
Lap
(Lap01)
Lap
(Lap02)
Stop Reset
Split Time
D
A A D A
Start
(
SPL
displayed)
Split Split release Stop Reset
E-25
Countdown Timer
You can set the countdown start time within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
&
(page E-7).
Second
s
Auto-repeat off
Start time
(Hours : Minutes)
E-26
To use the countdown timer
Press
'
while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops
if auto-repeat is turned off.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press
'
while a countdown operation is in progress to pause it.
• Press
'
again to resume the countdown.
• To stop a countdown timer operation completely, fi rst pause it (by pressing
'
),
and then press
$
. This returns the countdown time to its starting value.
E-27
To confi gure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
$
for about three
seconds until the hour setting of the countdown start
time starts to fl ash. This is the setting mode.
• If the countdown start time is not displayed, use
the procedure under “To use the countdown timer”
(page E-26) to display it.
2. Press
&
to move the fl ashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perform the following operations, depending on which setting currently is selected
on the display.
• While the start time setting is fl ashing, use ' (+) and % (–) to change it.
• While the auto-repeat on/off setting is fl ashing on the display, press ' to
toggle auto-repeat on (
) and off ( ).
l
l
l
l
l
l
l
l
l
l
l
Start time
(Hours : Minutes)
Auto-repeat on
E-28
4. Press
$
to exit the setting mode.
• The auto-repeat on ( ) is displayed on the Countdown Timer Mode screen while
this function is turned on.
E-29
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing
&
(page E-7).
Currently selected
World Time City
World Time
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5425 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5425 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5425

Casio 5425 User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info