624489
6
Zoom out
Zoom in
Previous page
1/14
Next page
Auto Time Calibration Signal
Receive
An automatic time calibration signal receive
operation is performed and the time and day
settings are adjusted between midnight and
5:00 a.m. Once a signal receive operation is
successful, no more auto receive operations
are performed that day.
The receive operation is performed only while
the
watch is in the Timekeeping Mode (normal
timekeeping).
Normally the mode hand points to the
current day of the week.
l Navigating Between Modes
30
Mode
hand
Place the watch near a window or some other
location appropriate for signal reception.
The second hand points to “RC” while time
calibration reception in progress.
When the receive operation is successful,
the time and day settings will be adjusted
automatically.
Note
Reception takes anywhere from
about two minutes to about 10
minutes. It can take as long as 20
minutes.
Checking the Receive
Operation Result
You can use the procedure below to check the
result
of the last GPS or time calibration signal
receive operation.
Getting ready
Enter the Timekeeping Mode.
l Navigating Between Modes
1.
Press (B).
The second hand will move and indicate
the receive operation result.
“Y (YES)”: Receive successful
“N (NO)”: Receive failed
30
Second hand
2.
Press
(B) or do not perform any operation
for one or two seconds to return to the
current time.
Note
Even if there was a successful
receive operation, the second hand
will point to “N (NO)” if you adjusted
the time setting manually.
If you do not perform any watch
operation for about one or two
seconds
after position information is
acquired, the watch will display the
acquired Home City (time zone) and
the rough latitude of your current
position.
30
Latitude
Home City
Signal Reception
Precautions
GPS signal and time calibration signal
reception will not be possible under any of
the watch conditions described below.
While battery power is low
While the watch is in the Airplane Mode,
Stopwatch Mode, Timer Mode, or Alarm
Mode
When power saving is at Level 2 (GPS
signal reception also is not possible at
Level 1.)
While the crown is pulled out
While a stopwatch elapsed time
measurement and/or timer countdown
operation is in progress
While
the temperature of the watch is less
than approximately -10°C (14°F) or
greater than approximately 60°C (140°F)
Note that an internal decoding process the
watch
performs after it receives a signal may
cause the time setting to be slightly off (by
less than one second).
If the receive operation is successful, the
time and day settings will be adjusted
automatically in accordance with the Home
City (time zone) and summer time settings.
Summer
time will not be applied correctly in
the cases described below.
When the summer time start date and
time, end date and time, or other rules are
changed by authorities
When position information cannot be
acquired correctly
When position information can be
acquired, but it is wrong because the
watch is located near a time zone
boundary, etc.
As of December 2013, China does not
observe summer time. If China starts to
observe
summer time in the future, the time
displayed by the watch for China may not be
correct.
When the watch is unable to adjust its time
in accordance with a calibration signal for
some reason, average timekeeping
accuracy is within ±15 seconds per month.
Operation Guide 5411
6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5411 - MRG-G1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5411 - MRG-G1000 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5411 - MRG-G1000

Casio 5411 - MRG-G1000 User Manual - German - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info