624955

Casio 5381 - BGA-180 Manual

3
Zoom out
Zoom in
Previous page
1/7
Next page
Operation Guide 5381
E-29
1. Enter the Thermometer Mode (page E-12).
2. Hold down A for at least two seconds until the temperature
value disappears from the display.
• When you release A the temperature value will start to fl ash.
• The hour and minute hands automatically move out of the way at
this time (page E-15).
3. Use D (+) and B (–) to calibrate the temperature value.
Calibration unit: 0.1°C (or 0.2°F)
Calibration range: –10.0 to 60.0°C (or 14.0 to 140.0°F)
Important!
• To cancel a temperature reading correction setting, hold down D and B at the
same time. The watch will beep.
4. Press A to return to the Thermometer Mode.
E-28
Correcting the Temperature Reading
The temperature sensor of this watch is adjusted at the factory and so further
adjustment is not required by you. However, if you notice that the readings
produced by the watch are different from readings produced by another instrument,
you can use the procedure in this section to make corrections. You also can use
this procedure to clear a correction.
Important!
• The watch will not be able to produce correct temperature readings if you make a
mistake during the correction procedure. Check to make sure that the value you
use for correction produces correct temperature readings.
• Before performing the following procedure, remove the watch from your wrist and
leave it for about 20 or 30 minutes to allow the case temperature to become the
same as the air temperature.
E-27
3. Press C.
• This will cause the current measurement
unit to fl ash.
4. Use D to select the measurement unit you
want.
5. Press A to return to the Thermometer Mode.
Important!
• When TYO (TOKYO) is selected as the Home City, the temperature unit is set
automatically to Celsius (°C). These settings cannot be changed.
D
E-26
Measurement unit: 0.1°C (or 0.2°F)
Measurement range*: –10.0 to 60.0°C (or 14.0 to 140.0°F)
* - -.- is displayed in place of the temperature when reading is outside the allowable
range.
2. Press C to return to the Timekeeping Mode.
To switch a temperature reading unit between Celsius (°C) and Fahrenheit (°F)
1. Enter the Thermometer Mode (page E-12).
2. Hold down A for at least two seconds until the temperature value disappears
from the display.
• When you release A the temperature value will start to fl ash.
• The hour and minute hands automatically move out of the way at this time (page
E-15).
E-25
Thermometer
This watch uses a temperature sensor to take temperature readings.
• You can select either Celsius (°C) or Fahrenheit (°F) as the temperature
measurement unit (page E-26).
To take a temperature reading
1. In the Timekeeping Mode, press D. This will enter the
Thermometer Mode, which is indicated by TEMP on
the display.
• If TEMP does not appear when you press D, press
it again (page E-12).
• The temperature reading will appear about one
second after TEMP.
• The reading is updated at fi ve-second intervals for two
to three minutes. After that, the watch automatically
returns to the Timekeeping Mode.
Temperature
E-24
Note
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• The day of the week changes automatically when the date changes.
E-23
3. When the timekeeping setting you want to change is fl ashing, use D and/or B
to change it as described below.
Screen To do this: Do this:
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Press D.
Reset the seconds to 00
Press D.
Change the hour or minute
Use D (+) and B (–).
Change the year
Use D (+) and B (–).
Change the month or day
Use D (+) and B (–).
4. Press A to exit the setting mode.
E-22
2. Press C to move the fl ashing in the sequence shown below to select the other
settings.
City Code
(page E-18)
C
DST
(page E-20)
C
12/24-Hour Format
C
Seconds
C
C
Hour
C
Illumination Duration
(page E-55)
Minutes
C
C
Button Operation Tone On/Off
(page E-59)
C
Day
C
Month
C
Year
E-21
Adjusting the Digital Time and Date Settings
Use the procedure below to adjust the digital time and date settings.
To confi gure the digital time and date settings
1. In the Timekeeping Mode, hold down A until ADJ
appears.
• This indicates the city code setting mode.
• The hour and minute hands automatically move out of
the way at this time (page E-15).
E-20
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until ADJ
appears.
• This indicates the city code setting mode.
• The hour and minute hands automatically move out of
the way at this time (page E-15).
2. Press C to display the DST setting mode.
3. Press D to toggle between Daylight Saving Time (ON)
and Standard Time (OFF).
• Note that you cannot switch between daylight saving
time and standard time while UTC is selected as your
Home City.
4. After the setting is the way you want, press A to
return to the Timekeeping Mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
DST indicator
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5381 - BGA-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5381 - BGA-180 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5381 - BGA-180

Casio 5381 - BGA-180 User Manual - German - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info