Manual Casio 5369 (page 3 of 8) (English)

586700

Zoom out

Zoom in

1/8

Operation Guide 5369 (MTG)

E-23

Timekeeping (Dual Time Mode)

To enter the Dual Time Mode, hold down C at least two seconds.

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Hour Hand (24-hour)

b Small Minute Hand: World Time minute hand

n Small Hour Hand: World Time hour hand

m Small Hour Hand (24-hour): World Time 24-hour hand

, Lower Dial Hand: Indicates the current day of the week.

. Day Indicator

x Pressing A causes the

Second Hand to move to the current Home City

for about one second.

x The

Day Indicator will change gradually between approximately 10 p.m.

and 2 a.m. During this period the number indicating the day will not be

centered in the indicator window.



B + *> @

5 6 

E-22



Dual Time Mode Stopwatch Mode

Alarm Mode Countdown Timer Mode

Indicates the day of the

week (SU/MO/TU/WE/TH/

FR/SA).

Indicates the 1/20 (0.05)

second count.

Indicates ON or OFF. Indicates TR.

x You can return to the Dual Time Mode from any other mode by holding down C for at least two

seconds.

E-21

Mode Reference Guide

Your watch has four “modes”. The mode you should select depends on what you want to do.

Use C to cycle between modes.

To do this: Enter this mode: See:

x View the current time and date in your Home City

x Conﬁ gure Home City and summer time (DST) settings

x Receive the time calibration signal automatically

x Manually adjust the time or date setting

Any Mode E-23

x View the current time in one of 29 other cities around the globe

x Perform manual time calibration signal reception

x View reception results

x Turn auto time calibration signal reception on or off

x Conﬁ gure World Time City and summer time settings

x Swap the Home City and World Time City

Dual Time Mode E-23

x Use the stopwatch to measure elapsed time

x Use Auto Start

Stopwatch Mode E-35

Use the countdown timer Countdown Timer Mode E-39

Set an alarm time Alarm Mode E-42

E-20

4. Rotate the crown to move the

Second Hand to the setting you want.

x To turn on auto receive, select Y (YES).

x To turn off auto receive, select N (NO).

5. Push the crown back in to return to the Dual Time Mode.

Radio-controlled Atomic Timekeeping Precautions

x Strong electrostatic charge can result in the wrong time setting.

x Even if a receive operation is successful, certain conditions can cause the time setting to be off by up

to one second.

x The watch is designed to update the date and day of the week automatically for the period from

January 1, 2000 to December 31, 2099. Updating of the date by signal reception will no longer be

performed starting from January 1, 2100.

x If you are in an area where signal reception is not possible, the watch keeps time with the precision

noted in “Speciﬁ cations” (page E-54).

x The receive operation is disabled under any of the following conditions.

− While power is at Level 2 or Level 3 (page E-11)

− While the watch is in the power recovery mode (page E-12)

− While the watch is in the sleep state (power saving, page E-13)

x A receive operation is cancelled if an alarm sounds while it is being performed.

E-19

To check the result of the latest receive operation

1. Hold down C for at least two seconds to enter the Dual Time Mode (page

E-23).

2. Press B.

x The

Second Hand will move to Y (YES) if the latest receive operation

was successful, or N (NO) if it was not. After about ten seconds, regular

timekeeping will resume.

x You can return to the Dual Time Mode manually by pressing any button

while the

Second Hand is pointing to Y (YES) or N (NO).

Note

x The

Second Hand will indicate N (NO) if you have adjusted the time or

date setting manually since the latest receive operation.

To turn auto receive on and off

1. Hold down C for at least two seconds to enter the Dual Time Mode (page

E-23).

2. Press B.

3. During the 10 seconds that the

Second Hand is pointing to the latest

receive operation result (see above), pull out the crown to the ﬁ rst click.

x This will cause the

Second Hand to point to either Y (YES) or N (NO),

which indicates the current on/off setting.

x Leaving the crown pulled out for more than two minutes without

performing any operation will automatically cause crown operations to

become disabled. If this happens, press the crown back in, pull it out,

and then start the operation over again.



N (NO)

Y (YES)



N (NO)

Y (YES)

E-18

To perform manual receive

1. Hold down C for at least two seconds to enter the Dual Time Mode (page E-23).

2. Hold down B for at least two seconds.

x The

Second Hand will ﬁ rst indicate the last receive results as either Y (YES) or N (NO), and then

move to RC (R) (Receive in progress) to indicate that signal reception has started.

3. The watch’s time setting is adjusted automatically whenever a receive

operation is successful.

Note

x The current time indication may become out of sync by two or three minutes

while a receive operation is in progress. Correct indication will resume after

the receive operation is complete. If you need to produce a correct time

reading immediately, press any button to stop the receive operation.

x If reception fails for some reason, check the surrounding area and eliminate

possible causes for failure and then try again. See “To get ready for a

receive operation” (page E-16).



N (NO)

Y (YES)

E-17

x Signal reception may be difﬁ cult or even impossible under the conditions described below.

Inside or among

buildings

Inside a vehicle Near household

appliances,

ofﬁ ce

equipment, or a

mobile phone

Near a

construction

site, airport, or

other sources of

electrical noise

Near high-

tension power

lines

Among

or behind

mountains

2. What you should do next depends on whether you are using Auto Receive or Manual Receive.

x Auto Receive: Leave the watch over night in the location you selected in step 1.

x Manual Receive: Perform the operation under “To perform manual receive” on page E-18.

Important!

x With Auto Receive, the watch performs the receive operation each day automatically up to six times

(up to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. When any

receive operation is successful, none of the other receive operations for that day are performed.

x Calibration signal reception is disabled in the following cases.

− While an elapsed time operation is in progress in the Stopwatch Mode

− While a timer operation is in progress

− While Auto Receive is turned off

− While the crown is pulled out

E-16

x Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception.

− Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

− Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

− Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

− Shangqiu (China) transmitter: 500 kilometers (310 miles)

x As of December 2012, China does not use Daylight Saving Time (DST). If China does go to the

Daylight Saving Time system in the future, some functions of this watch may no longer operate

correctly for the China time zones.

x Using this watch in a country covered by a time calibration signal that is different from the countries it

supports may result in incorrect time indication due to local application of summer time, etc.

To get ready for a receive operation

1. Place the watch in a location where signal reception is good.

12 o’clock

x Position the watch as shown in the nearby illustration,

with 12 o’clock pointed towards a window. Make sure

there are no metal objects nearby.

x Signal reception normally is better at night.

x The receive operation takes from two to 10 minutes, but

in some cases it can take as long as 20 minutes. Take

care that you do not perform any button operation or

move the watch during this time.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5369 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5369

Casio 5369 User Manual - German - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 5369 Manual

Product: