Manual Casio 5311 - GW-A1100 (page 8 of 11) (English)

624480

Zoom out

Zoom in

1/11

Operation Guide 5311

E-79

Adjusting Home Positions

Strong magnetism or impact can cause the hands and/or day indicator setting to be

off, even if the watch is able to perform the time calibration signal receive operation.

Auto Home Position Adjustment

Auto correction of hand home positions corrects the hand position automatically.

x Auto correction is performed in the Timekeeping Mode only.

x Auto correction corrects the positions of all hands. For the day Indicator, you must

perform the manual adjustment procedure under “To adjust home positions” (page

E-81).

x If the

Upper Dial Hand is 12 hours off of the current correct time, correct the

setting using the procedure under “To adjust home positions” (page E-81).

E-78

To turn the alarm on or off

In the Alarm Mode, press A to toggle the alarm between on and off. The

Second

Hand will indicate the current ON/OFF setting.

Note

x The alarm will not sound if battery power is low.

x The alarm will not sound if the watch is in the Power Saving sleep state.

To stop the alarm

Press any button.

E-77

x See “Using the Crown” (page E-4) for information about high-speed hand

movement.

4. Press C to switch to the hour setting mode.

x The

Hour Hand will move slightly left and right to indicate the

Hour Hand

setting mode.

x Check the 24-hour time indicated by the

Upper Dial Hand to see if the current

setting is a.m. or p.m.

5. Rotate the crown to adjust the hour setting only.

x See “Using the Crown” (page E-4) for information about high-speed hand

movement.

6. After the setting is the way you want, push the crown back in to exit the alarm

setting mode.

x The alarm always works based on the time kept in the Timekeeping Mode.

x The watch will return to the Timekeeping Mode automatically if you do not

perform any operation in the Alarm Mode for about two or three minutes.

E-76

To change the alarm time setting

1. In the Timekeeping Mode, press C four times to enter the Alarm Mode.

x The

Lower Dial hand will move to AL.

2. Pull out the crown to enter the alarm setting mode.

x If you do not perform any operation with the crown for about two minutes after

pulling it out, crown operations will become disabled and the watch hands will no

longer move when you rotate the crown. If this happens, push the crown back in

and then pull it out again.

x You can toggle between the hour and minute setting mode, and the hour only

setting mode by pressing C.

Hour/Minute Hour

3. Rotate the crown to set the alarm time.

x The

Hour Hand will also move.

E-75

Using the Alarm

When the alarm is turned on, an alarm will sound for about 10 seconds each day

when the time in the Timekeeping Mode reaches the preset alarm time. This is true

even if the watch is not in the Timekeeping Mode.

Hands and Indicators

Hour Hand: Indicates the currently set alarm time hour.

Second Hand: Indicates the current alarm ON/OFF

setting.

Minute Hand: Indicates the currently set alarm time

minute.

Upper Dial Hand: Indicates the hour setting of the

current alarm time in 24-hour format.

Lower Dial Hand: Points to AL.



B +

E-74

To perform a countdown timer operation

A A B

Start Stop Zero Reset

x A time-up alert sounds for 10 seconds when the countdown reaches 0, and then

the timer displays the start time.

x The alarm will not sound if battery power is low.

x Pulling out the crown while a countdown is in progress will stop the countdown and

enter the countdown start time setting mode.

Important!

x Time calibration signal reception is disabled while the watch is in the Countdown

Timer Mode.

To stop the alarm

Press any button.

E-73

To specify the countdown start time

1. In the Timekeeping Mode, press C three times to enter

the Countdown Timer Mode.

x The

Lower Dial Hand will move to TR.

2. In the Countdown Timer Mode, pull out the crown. This

enters the countdown start time setting mode.

x If you do not perform any operation with the crown for

about two minutes after pulling it out, crown operations

will become disabled and the hand will not move if

you rotate the crown. If this happens, push the crown

back in and then pull it out again.

3. Rotate the crown to set the countdown start time.

x The maximum countdown start time setting is

60 minutes. To set a countdown start time of

60 minutes, move the

Minute Hand to 12 o’clock.

x See “Using the Crown” (page E-4) for information about

high-speed hand movement.



E-72

Using the Countdown Timer

The countdown timer can be conﬁ gured within a range of one minute to 60 minutes.

An alarm sounds for about 10 seconds when the timer reaches zero.

Hands and Indicators

Second Hand: Indicates countdown or elapsed

seconds.

Minute Hand: Indicates countdown or elapsed minutes.

Lower Dial Hand: Points to TR.

x All hands move counterclockwise during a countdown.



E-71

x The

Second Hand, which indicates the 1/20 (0.05)-second count during

stopwatch operation, moves only 30 seconds after an elapsed time measurement

operation is started or restarted. After that, the

Second Hand stops.

E-70

To enter and exit the Stopwatch Mode

In the Timekeeping Mode, press C twice to enter the Stopwatch Mode.

x The

Lower Dial Hand will move to ST.

To perform an elapsed time operation

A A A B

Start Stop (Restart) (Stop) Zero Reset

To perform ﬂ yback timing

Pressing B while an elapsed time operation is in progress performs zero reset and

immediately resumes timing from there. You can do this as many times as you want.

B B

.....

A B

Start 1 Start 2 Start 3 Stop Zero Reset

x An ongoing elapsed time measurement operation is not affected by pulling out the

crown.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5311 - GW-A1100 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5311 - GW-A1100

Casio 5311 - GW-A1100 User Manual - German - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 5311 - GW-A1100 Manual

Product: