624818
3
Zoom out
Zoom in
Previous page
1/6
Next page
Operation Guide 5229
E-20
Lap Time
Lap time readings appear in the left digital dial. They show
the time elapsed since the last lap time reading was
taken.
If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting (page E-15).
If you want the watch to calculate the speed of the entire
race, specify the race distance for the distance setting
(page E-15). A speed will be indicated each time you
take a lap reading, but these lap speeds will not indicate
actual speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
LAP
(lap times) is shown in the left digital dial.
If
SPL
(split times) is displayed, press A to toggle it to
LAP
.
Lap time
E-21
To perform a lap time measurement
Select lap time (
LAP
) measurement and then perform the
following button operations.
D Start A Lap* A Lap* D Stop A Reset
* Lap time remains frozen in the left digital dial for about
12 seconds. After that, elapsed time measurement
reappears.
You can press A to take lap readings as many times as
you like.
While a lap time is displayed, the right digital dial will
alternate between the lap number (#01 to #99) and the
lap hour value. If you take more than 99 lap readings,
the lap number will restart from #00 following lap #99.
Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
lap.
Lap number
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
Hours
E-22
Split Time
Split time readings appear in the left digital dial. They
show the time elapsed since the beginning of the current
time measurement.
If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting (page
E-15).
For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based on
the total race distance, and so they will not indicate
actual intermediate split speeds.
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
SPL
(split times) is shown in the left digital dial.
If
LAP
(lap times) is displayed, press A to toggle it to
SPL
.
Split time
E-23
To perform a split time measurement
Select split time (
SPL
) measurement and then perform
the following button operations.
D Start A Split A Split Release* D Stop
A Reset
* The split time is released automatically if you do not
press A within about 12 seconds.
You can press A to take split readings as many times
as you like.
The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
Pressing A while a split time is displayed will switch
back to normal elapsed time measurement. The elapsed
time will appear in the left digital dial.
You also could press D to stop elapsed time
measurement instead.
Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
split (which is the overall elapsed time).
Hours
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
E-24
To measure times with the stopwatch
Elapsed Time
Lap Time
Split Time
D
Start
Stop Reset
D
➤➤
A
D
Start
(
SPL
displayed)
Split Split release Stop
A
D
A
➤➤
Reset
A
D
Start
(
LAP
displayed)
Lap
(Lap01)
Stop Reset
D
A
A
➤➤
A
Lap
(Lap02)
E-25
Countdown Timer
You can set the countdown start time within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Seconds
Auto-repeat off
Start time
(Hours : Minutes)
E-26
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown in the left digital
dial.
When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
If auto-repeat is turned off, the countdown time is reset to its starting value
automatically after the alarm stops.
If auto-repeat is turned on, the countdown will restart automatically without pausing
when it reaches zero.
The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-27
To configure countdown start time and auto-repeat settings
1. While the countdown start time is shown in the left
digital dial in the Countdown Timer Mode, hold down A
for about three seconds until the hour setting of the
countdown start time starts to flash. This is the setting
mode.
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-26) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perform the following operations, depending on which setting is currently selected
in the left digital dial.
While the start time setting is flashing, use D (+) and B (–) to change it.
To toggle auto repeat between on and off, press D while the on/off setting is
flashing in the left digital dial.
Start time
(Hours : Minutes)
Auto-repeat on
E-28
4. Press A to exit the setting mode.
The auto-repeat on (
) indicator is displayed on the Countdown Timer Mode
screen while this function is turned on.
E-29
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
Currently selected
World Time City
World Time
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5229 - GA-201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5229 - GA-201 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5229 - GA-201

Casio 5229 - GA-201 User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info