611481

Casio 5117 Manual

3
Zoom out
Zoom in
Previous page
1/7
Next page
Operation Guide 5117
3
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world. A simple operation swaps your
Home City with the currently selected World Time city.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code Table” for information about
the UTC offset settings that are supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
City code
Current time in
selected city
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zone).
Holding down the button scrolls at high speed.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping.
▲
Press A.
One second
DateHour : Minutes Seconds
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about three seconds to toggle
between Daylight Saving Time (DST indicator
displayed) and Standard Time (DST indicator not
displayed).
• The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
DST indicator
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time city. This
changes your Home City to your World Time city, and your World Time city to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
• If your current World Time city supports receipt of a time calibration signal, making it
your Home City enables calibration signal reception.
• For information about which cities support time calibration signal reception, see “To
specify your Home City.
To swap your Home City and World Time city
1. In the World Time Mode, use D to select the World Time city you want.
2. Hold down A and B until the watch beeps.
• This will make the World Time city (which you selected in step 1), your Home City. At
the same time, it changes the Home City you had selected prior to step 2 your World
Time city.
• After swapping the Home City and World Time city, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time city.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The digital display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch hand will perform one high-speed
rotation during the first second of an elapsed time
measurement operation. Then it will indicate the
seconds during the first minute of the operation. After
that, it will indicate minutes. Whenever an elapsed time
operation is stopped, the stopwatch hand will move to
the current seconds count.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
1/100 second
Hours
Minutes
Seconds
Stopwatch hand
SPL
indicator
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split
time and returns to elapsed time measurement.
• All of the operations in this section are performed in the Stopwatch Mode, which you
enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Clear
D
Start
Stop Re-start Stop
D
D
D
➤ ➤ ➤
A
➤
Split Time
D
Start Split
(SPL indicator
displayed)
Split release Stop
A
D
A
➤ ➤ ➤
Clear
A
➤
D
Start
Split
First runner
finishes.
Display time of
first runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
D
A
A
➤ ➤ ➤
Clear
A
➤
Two Finishes
Countdown Timer
You can set the countdown timer within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Minutes
Start time (minutes)
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero. The countdown is repeated up to eight times, and then stop.
• The number of the current repeat (1 to 8) is shown in the lower display.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about three
seconds until the minute setting of the countdown start
time starts to flash, which indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
C
3. Perform the following operations, depending on which setting is currently selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• While the auto-repeat on/off setting (
or ) is flashing on the display, press
D to toggle auto-repeat on (
) and off ( ).
l
l
l
l
l
l
l
l
l
l
l
Start time (minutes)
4. Press A to exit the setting screen.
• The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Alarms
When an alarm is turned on, the alarm tone sounds when
the alarm time is reached. One of the alarms is a snooze
alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered
, ,
and for the daily alarm, a snooze alarm
screen indicated by
. The Hourly Time Signal
screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a daily alarm, display an alarm screen ,
, and . To set the snooze alarm,
display the
screen.
•
is the hourly time signal setting.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A for about three seconds until the hour
setting of the alarm time starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
setting screen
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5117 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5117 in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5117

Casio 5117 User Manual - German - 7 pages

Casio 5117 User Manual - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info