Manual Casio 4334 (page 2 of 4) (English)

522107

Zoom out

Zoom in

1/4

Operation Guide 4334

To select the Single Stopwatch Mode or Dual Stopwatch Mode

In the Stopwatch Mode, press A to toggle the Single Stopwatch Mode and the Dual

Stopwatch Mode.

• You cannot toggle between the Single Stopwatch Mode and Dual Stopwatch Mode

while an elapsed time operation is in progress.

After pressing A to reset the elapsed time to all zeros, press A again to toggle

between stopwatch modes.

• The indicator “

ST1” indicates the Single Stopwatch Mode, while “ST2” indicates

the Dual Stopwatch Mode.

Remaining free records

Single Stopwatch

Mode Screen

Dual Stopwatch

Mode Screen

Press A.

▲

• Both the Single Stopwatch Mode screen and the Dual Stopwatch Mode screen show

the number of free memory records available for storing data. The watch’s memory

can hold up to 50 records total, including both Single Stopwatch Mode and Dual

Stopwatch Mode records.

Using the Single Stopwatch Mode

The Single Stopwatch Mode displays the total elapsed time and lap times for a single

vehicle or runner.

Stopwatch mode indicator

To perform a Single Stopwatch Mode operation

1. While the Single Stopwatch Mode screen is displayed,

press D to start elapsed time measurement.

2. To display a lap time, press D while elapsed time

measurement is in progress.

• After about 10 seconds, the upper display will change

automatically to timing of the next lap, with the total

elapsed time shown in the lower display.

• Each press of D during elapsed time measurement

stores the applicable lap number, lap time, and total

elapsed time in memory.

• Lap numbers are displayed in the range of 01 to 99.

After lap 99, pressing D does not display a lap time

(elapsed time continues without stopping).

• During the first hour, the stopwatch displays elapsed time in minutes, seconds,

and 1/100 second. After the first hour, the display changes to shows hours,

minutes, and seconds.

• Use the Recall Mode to view data in memory.

3. To stop elapsed time measurement and reset, press A.

Total elapsed time

Lap number

Lap time

Using the Dual Stopwatch Mode

The Dual Stopwatch Mode can be used to measure elapsed time for two vehicles or

runners at the same time, including separate lap times and the time differential

between vehicles or runners.

To perform a Dual Stopwatch Mode operation

The table below shows how to time two vehicles or

runners (Measurement A and Measurement B).

• The lower display shows Measurement A, while the

upper display shows Measurement B.

• In the Dual Stopwatch Mode, you can start timing from

either Measurement A or Measurement B.

Measurement B

Measurement A

• The lap number for the current displayed lap time (A or

B) appears in the center left of the display, and the

applicable lap time appears in the upper or lower display.

The other display (upper or lower) shows elapsed time

measurement.

• After about 10 seconds, the display will change

automatically to timing of the next lap.

• Each press of D or B during elapsed time

measurement stores the applicable lap number and lap

time in memory.

Measurement B Lap Time

Lap number

Measurement A Lap Time

Lap time screen

Start first

elapsed

time.

Press D.

Press B.

Display

lap time

screen.

Press D.

Press B.

Start other

elapsed

time.

Press B.

Press D.

Measurement A

Measurement B

Display lap

time of other

elapsed time.

Press B.

Press D.

Reset

elapsed

time to all

zeros.

Press A.

• Lap numbers are displayed in the range of 01 to 99.

After lap 99, pressing D does not display a lap time

(elapsed time continues without stopping).

• After starting Measurement A or Measurement B

elapsed time measurement and then starting the other

time's elapsed time measurement displaying a lap time

for one of the times will display the other time's lap time

and the difference between Measurement A and

Measurement B. After about 5 seconds, the display will

change automatically to timing of the next lap.

• After you press one of the buttons to display one of the

lap times (without the lap time differential displayed),

pressing the other button displays the other lap time and

the differential between the two laps for about five

seconds.

• The “±” indicator on the lap time differential screen

indicates both times are for the same lap.

• “-'--"--” is shown for the lap time differential if it is greater

than 10 minutes.

Measurement B

Lap Time

Measurement A and

Measurement B

differential

• Pressing A stops elapsed time measurement and reset.

• During the first hour, the stopwatch displays elapsed time in minutes, seconds, and

1/100 second. After the first hour, the display changes to shows hours, minutes, and

seconds.

• Use the Recall Mode to view data in memory.

Recalling Stopwatch Data

You can use the Recall Mode to recall and delete

stopwatch data stored in memory.

• Your watch automatically creates logs for storage of

stopwatch data in memory. For information about using

logs, see “Managing Memory Data”.

To recall stopwatch log data

1. Enter the Recall Mode.

• The title screen of the newest log appears first when

you enter the Recall Mode.

2. Use the A button to scroll through log title screens

until the one for the log you want to view is on the

display.

• Logs are numbered from 01 (oldest) to 50.

3. Press D (+) or B (–) to view the log data.

Log number

Log title screen

Log creation

date

Stopwatch mode in

which the recalled

log data was

measured

Press B.

Press D.

▲

Best lap indicator

Lap number of

best lap

Best lap

▲

Lap time

Lap number

▲

Total elapsed time

Recalled log data measured in the Single Stopwatch Mode (ST1)

Press B.

Press D.

▲

Recalled log data measured in the Dual Stopwatch Mode (ST2)

▲

Lap timeLap number

Lap time

Best lap indicator

Best lap

(Measurement A)

Best lap

(Measurement B)

▲

One second

later

Lap number of best lap

(Measurement B)

Lap number of best lap

(Measurement A)

The best lap time is for the best time in the newest log only. The Best Lap Time

screen is the one that has the best lap indicator.

To delete stopwatch data

1. In the Recall Mode, use A to scroll through log title screens until the one for the log

you want to delete is on the display.

• Displaying lap time data (not the log title screen), deleting the data also will delete

the log that contains the data.

2. Hold down B and D until the watch beeps and “

CLR” stops flashing on the

display.

• This will delete all of the data in the currently selected log.

• Deleting the newest log also will delete the best lap time data.

Countdown Timer

You can set the countdown timer within a range of one

minute to 100 hours. An alarm sounds when the

countdown reaches zero.

• You also can select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Second

Hours

Minutes

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is reset automatically to its starting value after the alarm stops.

• When auto-repeat is turned on, the countdown will restart automatically without

pausing when it reaches zero. The alarm sounds when the countdown reaches zero.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• To stop a countdown operation completely, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

To configure countdown start time and auto-repeat settings

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

display it.

2. Press C to move the flashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Minutes)

Auto-Repeat

On/Off

Start Time

(Hours)

Auto-repeat on indicator

On/Off status

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 4334 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 4334

Casio 4334 User Manual - German - 5 pages

Casio 4334 User Manual - Dutch - 5 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 4334 Manual

Product: