586687

Casio 3796 Manual

2
Zoom out
Zoom in
Previous page
1/4
Next page
2
Operation Guide 3796
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds in order to signal when the
countdown reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To set up the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Auto-repeat
Minutes
Hours
3. While a setting is flashing, use D and B to change it as described below.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
• When the digital time DST setting is on, the UTC differential can be set in a range
of –11.0 to +15.0 in 0.5-hour units.
5. Press A to exit the setting screen.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the left
of the hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
• The A and P indicators are not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting mode.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down D advances the analog time setting at
high speed.
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the high-
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (multi-function alarm, Hourly Time
Signal, or countdown beeper) starts to sound.
4. Press A to exit the setting mode.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting mode.
• To return to the Timekeeping Mode, press C.
4. When the setting you want to change is flashing, use D and B to change it as
described below.
Moon/Tide Data
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time at your Home Site.
• If you suspect that the current Moon/tide data is wrong
for some reason, check the current Timekeeping Mode
settings (time, date, and Home Site), and correct them if
required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator and “Tide Graph” for information
about the tide graph.
• All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
3. While a setting is flashing, use D (+) or B (–) to change it.
• You can specify a date in the range of January 1, 2000 to December 31, 2099.
4. Press A to exit the setting screen.
5. Use A to display either the tide data screen or the Moon data screen.
Countdown Timer
You can set the countdown timer within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using C.
• To specify a countdown start time of 24 hours, set
0:00
.
4. Press A to exit the setting screen.
•
The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen
while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
To view the current Moon/Tide Data Mode data
In the Moon/Tide Data Mode, press A to toggle between the tide data screen and the
Moon data screen.
• The tide graph shows the tide for the currently displayed time. The initial tide data
screen shows the level for 6:00 a.m. The Moon data screen shows the Moon age
and Moon phase for the current date.
Tide Data Screen Moon Data Screen
Press .
Tide
g
raph
Time
Moon a
g
e Year Month – Da
y
Year Month – Da
y
Moon phase indicator
• While the tide data screen is displayed, press D to advance to the next hour.
• While the Moon data screen is displayed, press D to advance to the next day.
• You can also specify a particular date (year, month, day) to view its tide data and
Moon data. See “To specify a date” for more information.
• When you enter the Moon/Tide Data Mode, the screen (tide data or Moon data) that
was displayed the last time you exited the mode appears first.
To specify a date
1. In the Moon/Tide Data Mode, hold down A until the
year setting starts to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Year
Month Day
To measure times with the stopwatch
Elapsed Time
Start
Stop Re-start Stop
Clear
Start
Split
(SPL displayed)
Split release Stop Clear
Start
Split Stop Split release Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
ScreenSetting
UTC Differential
Longitude Value
East Longitude/
West Longitude
Lunitidal Interval
Hours, Minutes
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –12.0 to +14.0,
in 0.5-hour units.
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of 0° to 180°, in
1-degree units.
Use D to switch between east longitude (
E
) and west
longitude ( ).
Use D (+) and B (–) to change the setting.
Tide Data Screen
Year Month – Day
Tide graph
Moon phase indicator
Time
Year
Month – Day
Seconds
Hours
Minutes
1/100 second
Timekeepin
g
Mode time
Seconds
Hours
Minutes
Screen
0:00
Do this:
Use D (+) and B (–).
Press D.
To do this:
Change the hours or minutes
Toggle auto-repeat on (
ON
) and off (
OF
)
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3796 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3796 in the language / languages: English as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3796

Casio 3796 User Manual - German - 4 pages

Casio 3796 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info