552992
2
Zoom out
Zoom in
Previous page
1/4
Next page
2
Operation Guide 3263
To toggle the Timekeeping Mode time between DST and Standard Time
Use 1. D to display the current Home City Time (T-1)
screen.
Hold down 2. A until the seconds start to flash, which
indicates the setting screen.
Press 3. C to display the DST setting screen.
Press 4. D to toggle between Daylight Saving Time
( displayed) and Standard Time ( displayed).
Press 5. A to exit the setting screen.
The DST indicator appears on the Timekeeping screen to
indicate that Daylight Saving Time is turned on.
DST indicator
12/24-Hour Format
With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Changing the City Setting of a Local Time
You can select any one of the city codes in the table at the back of this manual as a
Local Time city.
Display the Local Time whose city setting you want to change, and then hold down 1.
A for about one second until the current city code starts fo flash.
Use 2. D (east) and B (west) to select the city code you want.
Press 3. C to display the DST setting screen.
Press 4. D to toggle between Daylight Saving Time ( displayed) and Standard
Time ( displayed).
After the settings are the way you want, press 5. A.
Swapping the Home City Time with a Local Time
You can use the procedure below to swap the current Home City Time (T-1) with one
of the Local Times (T-2, T-3, T-4).
In the Timekeeping Mode, use 1. D to display the Local Time that you want to swap
with the Home City Time.
Press 2. A and B at the same time.
World Time
World Time shows the current time in 48 cities (31 time
zones) around the world.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time for another city code
In the World Time Mode, press D to scroll eastwardly
through city codes.
For full information about city codes, see the “City Code
Table”.
If the current time for a city is wrong, check your
Timekeeping Mode time and time zone settings and
make the necessary changes.
City code
Current time and date in
the zone of the selected
city code
To toggle a city code time between Standard Time and Daylight Saving Time
In the World Time Mode, use 1. D (east) to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
Hold down 2. A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
The DST indicator is on the display whenever you display
a city code for which Daylight Saving Time is turned on.
Note that the DST/Standard Time setting affects only
the currently displayed city code. Other city codes are
not affected.
Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
To change your Home Time city to the current World Time city
In the World Time Mode, use 1. D to display the city you want to make your new
Home Time city.
Press 2. A and B at the same time.
This makes the World Time city you selected in step 1 your new Home Time city.
Alarms
Your watch has a total of five alarms, each of which you
can configure as a daily alarm or one-time alarm.
Daily Alarm: Sounds at the preset time each day.
One-time Alarm: Sounds once at the preset time and then
is disabled automatically.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarms operate in coordination with the current Home
City Time.
DST indicator
Alarm on indicator
Alarm number
Alarm time
(Hour : Minutes)
To set an alarm time
In the Alarm Mode, use 1. D to scroll through the alarm
screens until the alarm number you want to set is
displayed.
After you select an alarm, hold down 2. A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation turns on the One-time Alarm automatically.
Press 3. C to move the flashing in the sequence shown below to select other
settings.
Hour Minutes
One-time Alarm/Daily Alarm Selection
While a setting is flashing, use 4. D and B to change it as described below.
Screen To do this: Do this:
Change the hour and
minutes. Use D (+) and B (–).
With the 12-hour format, set the time correctly
as a.m. or p.m. (P indicator).
/Toggle between One-
time Alarm and Daily
Alarm.
Press D.
One-time Alarm on:
Daily Alarm on:
Press 5. A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the
watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the
Home City Time (T-1).
To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
In the Alarm Mode, use 1. D to select an alarm.
Press 2. A to cycle through the alarm settings as shown below.
Alarm Off One-Time Alarm
On
Daily Alarm On
In all modes, the alarm on indicator is shown for the alarm that is currently turned
on.
The alarm on indicator flashes while the alarm is sounding.
To turn the Hourly Time Signal on and off
In the Alarm Mode, use 1. D to select the Hourly Time
Signal.
Press 2. A to toggle it on and off.
The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
Hourly time signal on
indicator
Countdown Timer
The countdown timer can be set within a range of one
second to 24 hours. An alarm sounds when the countdown
reaches zero.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing C.
Minutes
Hours
Seconds
1/10 second
To configure the countdown timer
While the countdown start time is on the display in the 1.
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
Press 2. C to move the flashing in the sequence shown
below to select other settings.
Hours Minutes Seconds
When the setting you want to change is flashing, use 3. D (+) and B (–) to change
the flashing item.
To specify a countdown start time of 24 hours, set .
Press 4. A to exit the setting screen.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3263 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3263 in the language / languages: English as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3263

Casio 3263 User Manual - German - 5 pages

Casio 3263 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info