586141
3
Zoom out
Zoom in
Previous page
1/15
Next page
Operation Guide 3134 3205
3
Note
When a calibration time is reached, the watch will receive the calibration
signal only if it is in either the Timekeeping Mode or World Time Mode.
Reception is not performed if a calibration time is reached while you are
configuring settings.
Auto receive of the calibration signal is designed to be performed early in
the morning, while you sleep (provided that the Timekeeping Mode time is
set correctly). Before going to bed for the night, remove the watch from your
wrist, and put it in a location where it can receive the signal easily.
The watch takes from two to 14 minutes to receive the time calibration
signal whenever a calibration time is reached. Do not perform any button
operation within 14 minutes before or after any one of the calibration times.
Doing so can interfere with correct calibration.
Remember that reception of the calibration signal depends on the current
time in the Timekeeping Mode. The receive operation will be performed
whenever the display shows any one of the calibration times, regardless of
whether or not the displayed time actually is the correct time.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being
received. For best reception, be sure to keep the watch in a location where
signal strength is strongest. The receiving indicator is displayed while an auto
or manual receive operation is in progress.
Receiving
indicator
Weak
(Level 0)
Strong
(Level 3)
Even in an area where signal strength is strong, it takes about 10 seconds
for signal reception to stabilize enough for the receiving indicator to indicate
signal strength.
Use the receiving indicator as a guide for checking signal strength and for
finding the best location for the watch during signal receive operations.
Following reception of the time calibration signal and calibration of the
watchs time setting, a settings updated indicator ( ) will remain on the
display in all modes. The settings updated indicator ( ) will not be
displayed if signal reception was unsuccessful or after you adjust the
current time setting manually.
The settings updated indicator ( ) appears only when the watch is able to
receive both time and date data successfully. It does not appear when only
time data is received.
The settings updated indicator ( ) indicates that at least one of the auto
calibration signal receive operations was successful. Note, however, that
the indicator disappears from the display each day at the start of the first
auto receive operation of the day.
To perform manual receive
1. Enter the Receive Mode.
2. Place the watch on a stable surface so its 12
oclock side is facing towards a window.
3. Hold down A for about two seconds until RC!
appears on the display.
Time calibration signal reception takes from
two to seven minutes, but in some cases it can
take as long as 14 minutes. Take care that you
do not perform any button operations or move
the watch during this time.
If the receive operation is successful, the
reception date and time appear on the display,
along with the GET indicator.
The watch will enter the Receive Mode if you
press A or if you do not perform any button
operation for about one or two minutes.
l
l
l
l
l
l
l
l
l
l
l
l
l
Receiving
Receive successful
If the current reception fails but a previous
reception was successful, the display shows
the previous receptions date and time, and the
ERR indicator. indicates that none of
the reception operations have been successful
during the current date.
The watch will enter the Receive Mode without
changing the time setting if you press A or if
you do not perform any button operation for
about one or two minutes.
Note
To interrupt a receive operation and return to
the Receive Mode, press A.
Receive failed
If there was a previously
successful reception
If no reception has been
successful
To turn auto receive on and off
1. Enter the Receive Mode.
2. In the Receive Mode, hold down E until the
current auto receive setting (ON or OFF)
starts to flash. This is the setting screen.
Note that the setting screen will not appear
if the currently selected Home City is one
that does not support time calibration
reception.
3. Press A to toggle auto receive on (ON) and
off (OFF).
4. Press E to exit the setting screen.
For information about city codes that support
signal receive, see To specify your Home
City.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
On/Off status
To check the latest signal reception results
Enter the Receive Mode.
When receive is successful, the display shows
the time and date that receive was successful.
indicates that none of the reception
operations were successful.
To return to the Timekeeping Mode, press D.
What you should do
Enter the Receive Mode
and try again.
Select one of the cities
to the left as your Home
City.
Perform manual signal
receive or wait until the
next auto signal receive
operation is performed.
Problem
Cannot perform
manual receive.
Auto receive is
turned on, but
the settings
updated
indicator ( )
does not appear
on the display.
Probable Cause
The watch is not in the Receive
Mode.
Your current Home City is not
one of the following: LON, PAR,
BER, ATH, HKG, SEL, TYO,
HNL, ANC, LAX, DEN, CHI, or
NYC
You changed the time setting
manually.
You changed the DST setting of
your Home City in the World
Time Mode.
You pressed a button while signal
receive was in progress.
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal
reception.
*Next day
5:00 am
5:00 am
About Auto Receive
The watch receives the time calibration signal automatically up to six times a
day. When any auto receive is successful, the remaining auto receive
operations are not performed. The reception schedule (calibration times)
depends on your currently selected Home City, and whether standard time or
Daylight Saving Time is selected for your Home City.
Your Home City Auto Receive Start Times
123456
LON Standard Time
1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
Daylight Saving Time
2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
PAR Standard Time
2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
BER
Daylight Saving Time
3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
ATH Standard Time
3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
Daylight Saving Time
4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
HKG,
SEL,
TYO
HNL,
ANC,
LAX,
DEN,
CHI,
NYC
Standard Time
Standard Time and
Daylight Saving
Time
Midnight
Midnight
1:00 am
1:00 am
2:00 am
2:00 am
3:00 am
3:00 am
4:00 am
4:00 am
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3205 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3205 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info