552994
4
Zoom out
Zoom in
Previous page
1/5
Next page
4
Operation Guide 3194
Graphic Areas
There are two graphic areas named A and B.
Graphic area B
Graphic area A
In all modes, graphic area A shows the Stopwatch Mode (ST1) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
In all modes, graphic area B shows the Stopwatch Mode (ST2) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
Flash Alert
When Flash Alert is turned on, the illumination flashes for
the alarms, the Hourly Time Signal, the countdown alarm,
and stopwatch (ST1) auto start.
To turn Flash Alert on and off
In the Timekeeping Mode, hold down D for about three
seconds to toggle Flash Alert on (Flash Alert indicator
displayed) or off (Flash Alert indicator not displayed).
Illumination flashes twice when you turn Flash Alert on
and once when turn Flash Alert off.
While Flash Alert is turned on, the Flash Alert indicator
remains on the display in all modes.
Note that pressing D to toggle Flash Alert on or off will
also switch timekeeping between 12-hour and 24-hour
format.
Button Operation Tone
The button operation tone sounds any time you press one
of the watchs buttons. You can turn the button operation
tone on or off as desired.
Even if you turn off the button operation tone, the
alarms, the Hourly Time Signal, the countdown alarm,
and stopwatch auto start all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on (mute indicator not displayed) and off (mute indicator
displayed).
Holding down C to turn the button operation tone on or
off also causes the watchs current mode to change.
The mute indicator is displayed in all modes when the
button operation tone is turned off.
Auto Return Features
If you leave the watch in the Tide/Moon Data or Alarm Mode for two or three minutes
without performing any operation, it automatically changes to the Timekeeping
Mode.
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
Resetting the seconds to
00
while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
00
without changing the minutes.
The year can be set in the range of 2000 to 2099.
The watchs built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watchs battery replaced.
World Time
All World Time Mode times are calculated from the current Home Site time in the
Timekeeping Mode using UTC offset values.
The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
The UTC offset is a value that indicates the time difference between a reference
point in Greenwich, England and the time zone where a city is located.
The letters UTC is the abbreviation for Coordinated Universal Time, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earths
rotation.
Illumination Precautions
The electro-luminescent panel that provides illumination loses power after very long
use.
Illumination may be hard to see when viewed under direct sunlight.
The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
Illumination turns off automatically whenever an alarm sounds.
Frequent use of illumination runs down the battery.
Mute indicator
Flash Alert indicator
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
Wear the watch on the outside of your wrist.
Warning!
Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch indicator displayed) or off (auto light switch indicator
not displayed).
The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
In order to protect against running down the battery, the auto light switch turns off
automatically approximately six hours after you turn it on.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
Moon Phase
Indicator
Moon Age
0.0 - 1.8
27.7 - 29.5
New
Moon
First
Quarter
(Waxing)
Full
Moon
Last
Quarter
(Waning)
1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0 - 16.6 16.7 - 20.2 20.3 - 23.9 24.0 - 27.6
Moon Phase
Moon phase (part you can see)(part you cannot see)
The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon
appears to wax and wane as the relative positioning of the Earth, Moon, and Sun
changes. The greater the angular distance between the Moon and the Sun,* the more
we see illuminated.
*
The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle. Since this watch performs calculations using integer values
only (no fractions), the margin for error of the displayed Moon age is
±1 day.
Tide Graph
The Tide Graph has six graphic segments, each of which indicates a different tide
level. The current tide level is indicated by the displayed graphic segment.
H L
High Tide
(Rising Tide) (Rising Tide)(Falling Tide)
Low Tide
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The tide graph of this watch
indicates tidal movement based on the Moons transit over a meridian and the lunitidal
interval. The lunitidal interval differs according to your current location, so you must
specify a lunitidal interval in order to obtain the correct tide graph readings.
The tide graph displayed by this watch is based on the current Moon age.
Remember that the margin for error of the Moon age displayed by this watch is ±1
day. The greater the error in a particular Moon age, the greater the error in the
resulting tide graph.
Lunitidal Interval
Theoretically, high tide is at the Moons transit over the meridian and low tide is about
six hours later. Actual high tide occurs somewhat later, due to factors such as
viscosity, friction, and underwater topography. Both the time differential between the
Moons transit over the meridian until high tide and the time differential between the
Moons transit over the meridian until low tide are known as the lunitidal interval.
When setting the lunitidal interval for this watch, use the time differential between the
Moons transit over the meridian until high tide.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3194 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3194 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3194

Casio 3194 User Manual - German - 6 pages

Casio 3194 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info