624494
4
Zoom out
Zoom in
Previous page
1/8
Next page
Operation Guide 3185
E-30
Moon Data
The Moon phase and Moon age information that appears first when you enter the
Tide/Moon Data Mode shows the data at noon for your currently selected Home City
on the current date, according to the Timekeeping Mode. After that you can specify
another date to view data.
If the Moon data is not correct, check your Timekeeping Mode settings and correct
them if necessary.
The Moon phase is displayed in the Timekeeping Mode, the Tide/Moon Data Mode,
and the Diving Mode.
If the watch is in the Diving Mode when there is a transition from one date to the
next, the Moon phase will not change to reflect the phase for the new date. If you
want to update the Moon phase, exit and then re-enter the Diving Mode.
If the Moon phase indicator shows a phase that is a mirror image of the actual Moon
phase in your area, you can use the procedure under “Reversing the Displayed
Moon Phase” (page E-34) to change it.
E-31
Tide/Moon Data Screens
In the Tide/Moon Data Mode, press A to toggle between the tide data screen and the
Moon data screen.
Tide Data Screen Moon Data Screen
Month Day
Current tide level
Moon ageTime Month Day
Press A.
Moon phase
E-32
When you display the Tide Data Screen, it initially shows tide data for 6:00 a.m.
Use the Tide Data Screen to specify the Tide Data time. You can use D (+) to
change the displayed time in one-hour increments.
Use the Moon Data Screen to specify the Tide/Moon Data date. You can use D (+)
to change the displayed date in one-day increments. Pressing D will display the
year of the displayed date.
Adjusting the High Tide Time
Use the following procedure to adjust the high tide time within a particular date. You
can find out high tide information for your area from a tide table, the Internet, or your
local newspaper.
E-33
To adjust the high tide time
1. In the Tide/Moon Data Mode, hold down A until the
hour digits start to flash.
2. Use D (+) and B (–) to change the hour setting.
3. When the hour is the setting you want, press C.
This will cause the minute digits to flash.
4. Use D (+) and B (–) to change the minute setting.
Pressing D and B at the same time while the time
adjustment screen is displayed (steps 2 through 4
above) will return the high tide time to its initial factory
default setting.
5. When the minute setting is the way you want, press A
to exit the adjustment screen and return to the Tide/
Moon Data Mode screen.
The high tide time setting is not affected by the DST
(summer time) setting of the Timekeeping Mode.
Hour
Minute
E-34
On some days, there are two high tides. With this watch, you can adjust the first high
tide time only. The second high tide time for that day is adjusted automatically based
on the first high tide time.
Reversing the Displayed Moon Phase
The left-right (east-west) appearance of the Moon depends on whether the Moon is
north of you (northerly view) or south of you (southerly view) as you view it.
You can use the procedure below to reverse the displayed Moon phase so it matches
the actual appearance of the Moon where you are located.
To determine the viewing direction of the Moon, use a compass to take a direction
reading of the Moon at its meridian passage.
For information about the Moon phase indicator, see “Moon Phase Indicator” (page
E-60).
E-35
To reverse the displayed Moon phase
1. In the Tide/Moon Data Mode, hold down A until the
hour digits start to flash.
2. Press C twice.
This will cause the Moon phase indicator to flash. This
is the indicator switching screen.
3. Press D to toggle the Moon phase indicator between
the southerly view (indicated by
) and northerly
view (indicated by
).
Northerly view: Moon is north of you.
Southerly view: Moon is south of you.
4. When the Moon phase indicator setting is the way you
want, press A to exit the switching screen and return
to the Tide/Moon Data Mode screen.
E-36
World Time
World Time shows the current time in 48 cities (31 time
zones) around the world.
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code Table” at the back of this
manual for information about the UTC differential
settings that are supported.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-11).
Current time in
selected city
City code
E-37
To view the time in another city
While in the World Time Mode, use D (eastward) to scroll through the city codes
(time zones).
Pressing D and B at the same time will jump to the UTC time zone.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
Note that the Standard Time/Daylight Saving Time setting affects only the currently
displayed city code. Other city codes are not affected.
Note that you cannot switch between Standard Time and Daylight Saving Time while
UTC is selected as the city code.
DST indicator
E-38
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
SIG) on and off.
There are five alarm screens numbered
AL1, AL2,
AL3 and AL4 for the one-time alarm, and a snooze
alarm screen indicated by
SNZ. The Hourly Time
Signal screen is indicated by
SIG.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-11).
Alarm number
Alarm time
(Hour : Minutes)
Current
time
E-39
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
To set a one-time alarm, display alarm screen AL1, AL2, AL3 or AL4.
To set the snooze alarm, display the
SNZ screen.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).
5. Press A to exit the setting screen.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3185 - GF-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3185 - GF-1000 in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info