Manual Casio 3134 (page 7 of 15) (English)

466632

Zoom out

Zoom in

1/15

Operation Guide 3134 3205

To display your current altitude

1. Press A in the Timekeeping Mode or in any

of the other sensor modes to enter the

Altimeter Mode.

•The watch will start altitude measurement

automatically, and display the result.

•It can take up to four or five seconds for the

altitude reading to appear after you enter

the Altimeter Mode.

2. Leave the watch in the Altimeter Mode if you

want the displayed altitude value and the

altitude graph contents to be updated at

regular intervals.

•Readings are taken at five-second intervals for the first three minutes

after you enter the Altimeter Mode. After that, readings are taken at two-

minute intervals.

•If you want to restart the altitude measurement operation at any point,

press A.

3. To stop the altitude measurement operation, press D to exit the Altimeter

Mode.

Current altitude

Altitude

graph

Current time

Notes

•Normally, displayed altitude values are based on the watch’s preset

conversion values. You also can specify a reference altitude, if you want.

See “Specifying a Reference Altitude”.

•Altitude is displayed in units of 5 meters (20 feet).

•The measurement range for altitude is –700 to 10,000 meters (–2,300 to

32,800 feet).

•The measured altitude may be a negative value in cases where there is a

reference altitude value set or because of certain atmospheric conditions.

•The displayed altitude value changes to xxxx meters (or feet) if a

measured altitude falls outside the measurement range. The altitude value

will be displayed again as soon as the measured altitude is within the

allowable range.

•You can change the measurement unit for displayed altitude values to either

meters (m) or feet (ft). See “To select the temperature, barometric pressure,

and altitude units”.

Saving Altitude Data

The watch automatically keeps track of the high altitude achieved to date.

You also can save altitude readings with the touch of a button.

•You can recall and view altitude data using the Data Recall Mode. For

details, see “Recalling Altitude Data”.

Automatic High Altitude Record

Whenever an altitude measurement in the Altimeter Mode is greater than the

currently stored high altitude value, the watch will replace the old value with

the new measurement automatically, along with the reading date and time.

This feature is always enabled and cannot be turned off.

•If the current reading is the same as the existing high altitude value, the

older value will be retained.

Saving an Altitude Reading

Perform the following procedure whenever you want to save an altitude reading.

To save an altitude reading

1. Press

to enter the Altimeter Mode.

2. Hold down

until REC flashes on the

display.

•At this time the watch will beep and the

current altitude reading value will be saved

along with the reading date (month - day)

and time.

3. REC will stop flashing and the watch will

return to the Altimeter Mode automatically

after data save is complete.

•Memory can store up to 24 altitude records. Storing a new reading while

there are already 24 in memory will delete the oldest record currently in

memory to make room for the new reading.

Specifying a Reference Altitude

After you specify a reference altitude, the watch adjusts its air-pressure-to-

altitude conversion calculation accordingly. The altitude measurements

produced by this watch are subject to error caused by changes in air

pressure. Because of this, we recommend that you update the reference

altitude whenever one is available during your climb.

To set a reference altitude

1. In the Altimeter Mode, hold down E for about

two seconds until either OFF or the current

reference altitude value starts to flash. This is

the setting screen.

2. Press A (+) or C (–) to change the current

reference altitude value by 5 meters (or 20 feet).

•You can set the reference altitude within the

range of –10,000 to 10,000 meters (–32,800

to 32,800 feet).

•Pressing A and C at the same time returns to OFF (no reference

altitude), so the watch performs air pressure to altitude conversions

based on preset data only.

3. Press E to exit the setting screen.

Altitude graph

The altitude graph shows Altimeter Mode

measurement results.

•The vertical axis of the graph represents

altitude, and each dot stands for 10 meters (40

feet).

•The horizontal axis represents time, and the flashing dot in the rightmost

column indicates the latest measurement result. For the first three minutes,

each dot represents five seconds. After that, each dot represents two

minutes.

•An out of range measurement result or a measurement error will cause the

column of dots for that measurement to be blank (skipped).

Time

Altitude

Recalling Altitude Data

In the Data Recall Mode, you can recall and view altitude reading records you

stored in the Altimeter Mode, as well as the high altitude record.

•All of the operations in this section are performed in the Data Recall Mode.

Data Screens

The following explains the contents of each of the screens that appear in the

Data Recall Mode.

To delete all altitude data currently in memory

1. In the Data Recall Mode, hold down E until

CLR flashes on the display and the watch

beeps twice.

•Releasing E at any time while CLR is

flashing on the display will cancel the delete

operation.

2. Keep E depressed for two seconds.

•The watch will beep to indicate that all of the

altitude data stored in watch memory (including

readings you stored and the high altitude

value) is deleted.

When you measure altitude using a reference altitude specified by you

After you specify a reference altitude, the watch uses that value to convert the

current measured barometric pressure value to altitude.

•When mountain climbing, you can set the

reference value in accordance with a marker

along the way or altitude information from a

map. After that, the altitude readings

produced by the watch will be more accurate

than they would without a reference altitude.

Displaying Your Current Altitude

You can use the procedure described in this section to display your current

altitude. If you leave the watch in the Altimeter Mode, it will update the

displayed altitude value regularly, and indicate reading-to-reading changes in

the altitude graph at the top of the display.

Important!

•The procedure in this section simply displays values indicating your current

altitude, without storing them in watch memory. For information about

recording altitude readings in watch memory, see “Saving Altitude Data”.

400

Note

•While the altitude record or high altitude screen is displayed, the bottom

part of the display alternates between the measurement date (month and

day) and measurement time, at 1-second intervals.

Altitude

Measurement date

(Month – Day)

▲

Alternates at

1-second intervals.

Measurement time

(Hour : Minute)

Altitude

record

indicator

To view altitude reading records and the high altitude record

1. Enter the Data Recall Mode.

•After about one second a record with MAX on the top will appear. This is

the high altitude record.

2. Use A (+) and C (–) to scroll through the other altitude reading records.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3134 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3134

Casio 3134 User Manual - German - 16 pages

Casio 3134 User Manual - Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 3134 Manual

Product: