Operation Guide 2760 2761
4
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in.
of sev
The target alarm counts the time remaining from the current time in your Home
Zone until the target alarm time.
day
• Alarm and Hourly Time Signal operations are perf
Timekeeping Mode digital time.
• Pressing any b
• P
snooze alarms cancels the current snooze alarm operation.
Displaying the
Displaying the snooz
AL5
) setting screen
T
In the Alarm Mode, hold down B to sound the alarm.
T
1. In the Alarm Mode, use B to select an alarm or the
Hourly Time
2. Press A to toggle it on ( on displayoF
displayed).
• YAL1 to
AL5) or the Hourly Time Signal in order to chec
current on/off status.
• T
indicator on its Alarm Mode screen and in all modes.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Snooze alarm indicator
On/Off status
Hourly
Timekeeping
Use the
also explains ho
• All of the operations in this section are perf
you enter by pressing C.
▲
▲
▲
▲
▲
Press A .
Last Signal Screen
Day of week Month – Day
Press B .
Year Month – Day Hour : Minutes
PM indicator
Seconds
Setting the Digital
Make sure you select y
date settings.
Timekeeping Mode settings.
if you do not select the proper Home
Timekeeping Mode.
• When setting the time and date, y
Zone (the time zone where you normally use the watch), summer time (Da
Saving time or DST), 12/24-hour f
T
1. While any screen other than the last signal screen is on
the display in the A
until the GMT differential v
indicates the setting screen.
• The second hand will move at high speed to the 12
o’ clock position, where it will stop
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
GMT differential value
• The GMT differential v
Greenwich Mean
• The DST indicator indicates that Daylight Sa
for the currently selected time z
2. Use D (+) and B (–) to select the time zone you want to use as y
Zone.
• For full details about GMT diff“Time Zone ”.
3. Press C to move the flashing in the sequence shown belo
settings.
4. When the setting you want to change is flashing, use B and D to change it as
described below
12/24-Hour
Format
GMT differential
value
DST
Power
Saving
Day
Hour
Minutes
Seconds
Year
5. Press A to exit the setting screen.
• When you e
match the digital time.“Analog Timekeeping ” f
Screen T
Change the time zone
Ton ),
Standard Time OFF ), or Auto DST (A)
T12H ) and 24-hour
(24H ) timekeeping
Reset the seconds to 00
Change the hour or minutes
Change the year
Ton ) and off ( OFF)
Do this:
Use D (+) and B (–).
Press D.
Press D.
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Press D.
• Auto DST ( A) can be selected only while +0.0, +1.0 or +2.0 is selected as the Home
Time Zone.“ Da” belo
Daylight Sa
Daylight Sa
Standard
Saving Time
The time calibration signals include both Standard
DST setting is turned on, the watch switches between Standard
(summer time) automatically in accordance with the signal it receives
• The auto DST setting can be turned on only while +0.0, +1.0 or +2.0 is selected as
the Home Time Zone
• If you e
probably best to s
time) manually
T
1. While any screen other than the last signal screen is on the display in the
Timekeeping Mode, hold doA until the GMT differential v
which indicates the setting screen.
2. Press C to display the DST setting screen.
3. Press D to cycle through the DST settings in the sequence shown below
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate that Da
turned on.
Auto DST (A) DST off (OFF) DST on (on)
Analog Timekeeping
The analog time of this watch is synchronized with the digital time
setting is adjusted automatically whenev
Note
• The hands for the analog timepiece mo
the follo
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home
• Whenev
make sure you adjust the digital setting first.
• Depending on how much the hands ha
time, it may tak
T
1. In the C fiv
the Hand Setting Mode.
2. Hold down A until – 0 0 – starts to flash, which
indicates the analog setting screen.
• The second hand will move at high speed to the 12
o’ clock position, where it will stop
3. If the second hand is not pointing precisely at 12 o’clock
at this time, use D to adjust its position.
• Each press of D causes the second hand to advance
by one second.
4. Press C .
on the digital display to flash, which indicates that
adjustment of hour and minute hands is selected.
5. Use D (+) and B (– ) to mov
units.
• Holding down either button mo
speed.
Minute hand
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Second hand
Hour hand
24-hour dial
• Adjust the analog time so it matches the digital time.
hand moves in coordination with the hour and min
analog time, keep an e
correct am/pm position.
• TD , press B , and then release
both buttons.
• TB , press D , and then release
both buttons.
• The abov
button or until the hands complete one 24-hour cycle (two re
movement also stops if an alarm starts to sound.
6. Press A twice to exit the setting screen.
• The first press of A causes 00:00.00 to appear on the display (indicating the
stopwatch 1/20 second dial hand adjustment screen).A the second time
exits the setting screen.
• TC.
Illumination
T
watch for easy reading in the dark.
The watch’s auto light switch automatically illuminates the
face when y
• The auto light switch m
the auto light switch on indicator) f
• Y
illumination duration.
• See “Illumination Precautions ” for other important
information.
T
In any mode (eD to illuminate
the face of the w
• The above oper
setting.
Auto light switch
on indicator
T
1. While any screen other than the last signal screen is on
the display in the A
until the GMT differential v
indicates the setting screen.
2. Press C three times to move the flashing to the
second setting.
3. Press B to toggle the illumination duration setting
between 2 seconds (“. ” displayed in front of seconds)
and 1.5 seconds (“. ” not displa
4. Press A to exit the setting screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
