586704

Casio 2412 Manual

5
Zoom out
Zoom in
Previous page
1/7
Next page
USER’S GUIDE 2412
5
COM
1‰
:
58
INFRA RED
INFRA RED
▲
After about
one second
COM.MENU
WatchPC
Other (PDA, etc.)
Portable game device
COM.MENU
SEND
RECEIVE
IR Mode
Use the IR Mode to exchange data between two watches or between your
watch and computer, or some other device.
• The following shows compatibility of data communication between this watch
and other CASIO Wrist Camera Models.
Note
An infrared adapter or an IR port is required to exchange data with this watch.
The following procedure covers data communication between two watches
only. See the CD-ROM that comes with the watch and the documentation that
comes with the infrared adapter for information about data communication with
a computer.
Exchanging Data Between Two Watches
• To exchange data between two watches, orient the watches as shown above.
• The 10cm (4 inches) and 30-degree maximums shown in the above
illustration apply only when the watches are pointed straight at each other.
The maximum allowable distance may be less if either watch is at an angle
(not pointed straight).
• At an angle of 15 degrees or more, you may need to move the two watches
very close to each other.
To enter the IR Mode
In the Timekeeping Mode, press D twice to enter the IR Mode.
• An initial screen appears for about one second, followed by the
COM. MENU screen.
To send an image
1.On the COM. MENU screen, use B or E to
select watch ( ).
2. Press F to display the watch-to-watch send
menu.
3. Press C to display the image selection screen.
• Each press of C toggles between the image and
the send menu.
• The watch automatically returns to the send
menu if you leave an image on the display for
about five seconds.
10cm (4 inches) maximum
15 degree maximum
SEND
2‰‰1. 6.3‰.P1‰:58
Wrist Camera Model
WQV-3 series (Module 2411)
WQV-1/WQV-2 series
(Module 2220)
Communication with this watch
Supported
Not supported (different protocol)
4.Use E(+) and B (–) to scroll through the images
and display the one you want to send.
• SEND is displayed in the upper left corner of the
image screen.
• You can send only one image at a time between
watches.
5.Align the IR ports of the two watches with each
other.
• Put the receiving watch into receive standby at
this time. See “To receive an image” for more
information.
SEND
OK
SEND
6.On the sending watch, press F to send the
displayed image.
• The data send screen shown nearby appears
while an image send operation is in progress.
• The message OK appears momentarily after the
image send operation is complete. Next, the
watch returns to the send menu.
• Pressing A during the above procedure displays
the COM. MENU screen.
• After you are finished sending images, press D
to return to the Timekeeping Mode.
To receive an image
1.On the COM. MENU screen, use B or E to
select watch ( ).
2.Press F to display the watch-to-watch send
menu.
3.Press E to display the watch-to-watch receive
menu.
• Pressing B returns to the watch-to-watch send
menu.
4.Press F to enter receive standby.
5.Align the IR ports of the two watches with each
other, and perform the send operation on the
sending watch.
• See “To send an image” for more information.
• The message OK appears momentarily, followed
by the received image. Next, the watch returns to
the receive menu.
• Pressing A during the above procedure displays
the COM. MENU screen.
• After you are finished receiving images, press D
to return to the Timekeeping Mode.
SEND
RECEIVE
Communication Errors
Screen messages appear in the IR Mode to let you know when there is a
problem with data communication. When this happens, check the following to
find out what you need to do. Also, you can avoid data communication
problems by carefully observing the advice under “Communication
Precautions”.
Communication Screen Messages
Other Messages
Communication Precautions
• The two IR ports must be within 10cm (4 inches) and 30 degrees of each
other.
• Proper data communication may also be impossible if the two IR ports are
too close to each other.
• At an angle of 15 degrees or more, you may need to move the two IR ports
very close to each other.
• Do not move the watch while communication is in progress.
• Make sure there is nothing between the two IR ports that blocks the path of
the IR signal.
• Infrared communication may not be possible in areas where lighting is bright,
near a window, etc.
• In the case of inverter fluorescent lighting or other very strong light, try
turning off the light or move to an area where light is not shining directly onto
the infrared ports.
• An unrelated nearby IR data communication operation can interfere with
proper IR data communication.
• The maximum allowable distance between the IR ports may be less than
10cm when watch battery power is low.
• The watch automatically returns to the COM. MENU screen about five
minutes after the image selection screen or receive standby screen is
displayed. If the point where five minutes elapse occurs while a data send/
receive operation is in progress, the operation continues until it is complete,
after which the watch automatically returns to the COM. MENU screen.
ERROR SEND
(Sender),
ERROR RECEIVE
(Receiver)
MEMORY FULL
Data send or receive failed for some reason.
Tr y again.
Memory of the receiver is full. Delete data you
no longer need and try again.
Something is interfering with proper data
communication. Correct the cause of the
problem. If data communication is not restored
within about 25 seconds, ERROR appears on
the display.
SEND
RECEIVE
(Receiver)
(Sender)
CHECKING DATA
REC ERROR
This message appears when an image is being
processed after data is received.
Data cannot be saved because some problem
occurred while accessing flash memory.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 2412 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 2412 in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 2412

Casio 2412 User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info