799650
5
Zoom out
Zoom in
Previous page
1/39
Next page
- For sawing on a curve, use the special “curved
cut” blade, which is thin enough to saw along a
curve.
PERFORATING WOOD (FIG 5)
- To perforate wood, there are two possibilities:
- 1. Drill a hole and begin sawing from that point.
- 2.Use the following technique (see fig. 5):
- Place the jig-saw on the rounded edge loca- ted
at the front of the bottom plate.
- Turn on the saw and slowly lower it until it
touches the material to be sawed.
- Once the material has been perorated, return
the saw to its normal position and continue
sawing.
ONCE YOU HAVE FINISHED
USING THE APPLIANCE
- Stop the appliance by releasing the pressure on the
on/off switch.
- Unplug the appliance from the mains.
- Clean the appliance.
MAINTENANCE AND CARE
- WARNING! Always unplug the machine before
carrying out work on it.
- Checking the saw blade: deposits of resin and glue
on the saw blade cause inefficient cutting. To avoid
them, always clean the blade immedi- ately after use.
- Inspect the mounting screws: regularly inspect all
the mounting screws and ensure they are firmly
tightened. Should any screw be loose, tighten it
immediately. Failure to do so could put you at serious
risk.
- The vents should always be kept clean and free of
obstacles.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
CLEANING
- Disconnect the appliance from the mains and allow
it to cool before undertaking any cleaning task.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning
the appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of
cleanliness, its surface may degrade and inexorably
affect the duration of the appliance’s useful life and
could become unsafe to use.
SUPPLIES
- Supplies can be acquired from distributors and
authorised establishments (such as filters, etc.) for
your appliance model.
- Always use original supplies, designed specifi- cally
for your appliance model.
ANOMALIES AND REPAIR
- Take the appliance to an authorised technical
support service if product is damaged or other
problems arise. Do not attempt to disassemble or
repair the appliance yourself as this may be dangerous.
- If the connection to the mains has been dama- ged,
it must be replaced, take the appliance to an
authorised technical support service. Do not attempt
to disassemble or repair the appliance by yourself in
order to avoid a hazard.
SPECIFICATIONS
- Rated power 400W
- Rated voltage 220-240V
- No load speed 3000 rpm
- Wood cutting Capacity 55mm
- Steel cutting Capacity 4mm
- Aluminum cutting capacity 8mm
- Slant up to: 45º
- Weigth 1,37Kg
- Sound pressure level < 85 dB(A)
- Sound power lvl < 96dB(A)
- Vibration < 10.85 m/s2
- NB: These specifications are subject to change
without notice of purpose of improvement.
- Measured sound level determined according EN
60745-1
- The vibration emission level given in this infor-
mation sheet has been measured according EN 60745-
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casals SA400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casals SA400 in the language / languages: All languages as an attachment in your email.

The manual is 1.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info