722460
19
Zoom out
Zoom in
Previous page
1/48
Next page
19 // GB
SHOWTIME... ALMOST!
Engine break-in is the most important step to assuring that your
engine is fast and reliable throughout its life. Put simply: DON’T
SKIP THIS PART!
The engine is pre-set from the factory for break-in. Use a “FAT
BONE” 50 090 5034 or platform and place the car so that the wheels
are off the ground and free.
Make sure the throttle is set at neutral with your radio. Place the
glow heater onto the glow plug and give the recoil a sharp pull
(picture 4). Do not pull it more than twelve inches! More than that
may break the cord and this is not covered under warranty. It is
better to give the recoil short sharp pulls rather than long ones. If
the pull-start cord gets stuck, rotate the flywheel a little bit with
your finger. This should make the cord automatically recoil. Within
a few pulls, the engine will start with a good puff of smoke.
4
If the engine has trouble idling at the rich setting, turn the idle
screw clockwise 1/8th of a turn at a time. This will increase the idle
allowing the car to break-in properly. Try to do this in a well-venti-
lated area, such as your driveway. Unburned oil from the fuel will
accumulate under the exhaust, so be prepared. Let the car idle like
this for 2 - 3 tanks of fuel checking the engine temperature every 2
minutes.Pleaseallowabreakof10–15inbetweenfillingthetank
to allow the engine to cool down. You should be able to touch the
head of the engine with your fingertips and it will be hot, but not
uncomfortably so. (Attention! Do not touch!) If it seems very hot,
richen (turn counter-clockwise) the high-end and low-end needles
1/8th of a turn. Always use small increments when making these
kinds of adjustments.
Racer Tip:
Factory setting of carburettor:
With the following basic adjustment the engine starts immediately,
running perfect and rich enough (outside temperature 8°C).
• Idlestopscrew:approx.1mmairgap;
• Highspeedneedlevalve:screwincompletely,thenopen4full
turns;
• Lowspeedneedlevalve(linking):flushwiththeedgeofthe
linking arm, then 1 full turn clockwise;
After run-in is finished the high speed needle valve should be open
at least 3 and 1⁄4 turns. A richer setup is better if outside tempera-
ture is high.
5
rich lower
6
rich
low RPM
lower
high RPM
Racer Tip:
Drive your car slowly with the rich setting shortly after the break-in
period avoiding prolonged periods at full throttle. Gradually lean
out the mixture 1/8 of a turn at a time. The idle will increase the
more you lean the engine out.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carson Virus 4.0 GP V32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carson Virus 4.0 GP V32 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 29,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info