722459

Carson CY Pro Chassis Manual

21
Zoom out
Zoom in
Previous page
1/100
Next page
CARSON CY Pro Chassis 21
GB
f. Showtime... almost!
Engine break-in is the most important step to assuring that your
engine is fast and reliable throughout its life. Put simply: DON’T SKIP
THIS PART!
The engine is pre-set from the factory for break-in. Use a “FAT BONE” 50
090 5034 or platform and place the car so that the wheels are off the
ground and free.
Make sure the throttle is set at neutral with your radio. Place the glow
heater onto the glow plug and give the recoil a sharp pull (picture 4).
Do not pull it more than twelve inches! More than that may break the
cord and this is not covered under warranty. It is better to give the
recoil short sharp pulls rather than long ones. If the pull-start cord gets
stuck, rotate the flywheel a little bit with your finger. This should make
the cord automatically recoil. Within a few pulls, the engine will start
with a good puff of smoke.
If the engine has trouble idling at the rich setting, turn the idle screw
clockwise 1/8th of a turn at a time. This will increase the idle allowing
the car to break-in properly. Try to do this in a well-ventilated area,
such as your driveway. Unburned oil from the fuel will accumulate
under the exhaust, so be prepared. Let the car idle like this for 2 - 3
tanks of fuel checking the engine temperature every 2 minutes. Please
allow a break of 10 – 15 in between filling the tank to allow the engine
to cool down. You should be able to touch the head of the engine with
your fingertips and it will be hot, but not uncomfortably so. (Attention!
Do not touch!) If it seems very hot, richen (turn counter-clockwise)
the high-end and low-end needles 1/8th of a turn. Always use small
increments when making these kinds of adjustments.
Racer Tip:
Factory setting of carburettor:
With the following basic adjustment the engine starts immediately,
running perfect and rich enough (outside temperature 8°C).
• Idle stop screw: approx. 1 mm air gap;
• High speed needle valve: screw in completely, then open 4 full
turns;
• Low speed needle valve (linking): flush with the edge of the linking
arm, then 1 full turn clockwise;
After run-in is finished the high speed needle valve should be open at
least 3 and 1⁄4 turns. A richer setup is better if outside temperature is
high.
Racer Tip:
Drive your car slowly with the rich setting shortly after the break-in
period avoiding prolonged periods at full throttle. Gradually lean out
the mixture 1/8 of a turn at a time. The idle will increase the more you
lean the engine out.
Picture 4
rich lower
rich
lower
low
RPM
high
RPM
Picture 5
Picture 6
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carson CY Pro Chassis at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carson CY Pro Chassis in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 32,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info