583651
19
Zoom out
Zoom in
Previous page
1/188
Next page
19
Space Sensor Control
Space sensor staging control is an adaptive anticipation control that
weighs the actual space demand against the trend of that demand
and the trend of the supply air. It also honors stage time guards
and supply air limits. The demand for cooling in the space is
displayed as the Cooling Demand (Run StatusCOOL
DMD.C). The control tries to anticipate the change in the space
because of its current stage status. This anticipation is based on the
SupplyAir Trend (Operating ModesCOOLSA.TR) and the
Cool Demand Trend (Operating ModesCOOLTRD.C).
These trends will show the control how the space is reacting to the
current running conditions and help it decide when to add or
remove one stage from the requested stages. The Cool Stage
Increase Time (ConfigurationCOOLC.INC) or the Cool
Stage Decrease Time (ConfigurationCOOLC.DEC) has to
expire before another stage can be added or a stage can be
subtracted. If at any time the SupplyAir Temperature (SAT) falls
below the Minimum Supply Air Temperature Upper Level
(ConfigurationCOOLSATSAT.U), the requested stages
will not be allowed to increase. If at any time the SAT falls below
the Minimum Supply Air Temperature Lower Level
(ConfigurationCOOLSATSAT.L), the requested stages will
be reduced by one without honoring C.DEC. If SAT.L and SAT.U
are configured so that they are close together, the last stage of
compressor might cycle rapidly, slowed only by its minimum on
and offtime requirements.
Compressor Control
The compressor control works hand and hand with the staging
control. As the staging control requests stages, the compressor
control determines what actual compressors are available or
running and tries to provide stages for what is requested. The
availability of a compressor depends on time guards, circuit
diagnostics, outdoor temperature, and the unit size.
The Number of Circuits (ConfigurationCOOLN.CIR)
configuration tells the control how many compressors are installed
on the unit. The Circuit A Lockout Temp
(ConfigurationCOOLCIR.A CA.LO), Circuit B Lockout
Temp (ConfigurationCOOL CIR.BCB.LO), and Circuit C
Lockout Temp (Configuration COOLCIR.CCC.LO)
configurations set the outdoor temperature in which the respective
compressor is allowed to run down to. Timeguard A (Run
StatusCOOLCIR.ATG.A), Timeguard B (Run
StatusCOOLCIR.BTG.B), and Timeguard C (Run
StatusCOOLCIR.CTG.C) display the time a respective
compressor has before it is available for use. Individual circuit
diagnostic tests are performed during operation which may or may
not allow a compressor to be used. The configuration point
Compressors On Circuit A (Configuration COOLN.A)
informs the control to run diagnostics on one or two compressors
for circuit A. The available stages at any given time are displayed
as Available Compressors (Run StatusCOOL AVL.C). The
actual compressors running at any given time are displayed as
Actual Cooling Stages (Operating ModesCOOL ACT.C).
Compressor A (Run StatusCOOLCIR.A CMP.A),
Compressor B (Run StatusCOOLCIR.B CMP.B), and
Compressor C (Run StatusCOOLCIR.C CMP.C) are
displayed on when the respective compressor is running.
There are time guards to protect the compressors. Compressor Min
On Time (ConfigurationCOOLMRT.C) and Compressor Min
Off Time (ConfigurationCOOLMOT.C) apply before a
compressor can be turned back on or turned off.
Outdoor Fan Control
Each unit has a means for variable outdoor airflow to control
condenser pressure control within an acceptable range by
responding to varied operating modes and ambient temperatures.
This is implemented differently on different units using
multispeed motors, multiple outdoor fans, or variablespeed
motor controllers.
NOTE: Factory default configurations account for these model
differences and should not be changed. The default configurations
have been qualified over a large range of conditions and are
provided in case a field replacement of a control board occurs and
the settings need to be checked or manually configured. Outdoor
fan operation is further described below to assist in
troubleshooting.
The outdoor fans are controlled by levels. There are 4 levels of
operation (03) and the current operating level is shown as
Outdoor Fan Level (Operating ModesCOOLF.LEV). The
fan level selected during operation is based on factory
configurations of outdoor temperature limits and condenser
pressure limits. These are in the Outdoor Fan Control submenu
(ConfigurationCOOLOFC) and shown in Table 5. The
starting level is picked after a compressor is turned on and is based
on the Outdoor Air Temperature (TemperaturesAIR.TOAT).
A circuits Saturated Condensing Temperature (Temperatures
REF.TSCT.x) can override the fan level at any time if the
specific Fan Level Max Pressure (ConfigurationCOOLOFC
x.MXP) is exceeded. This override will end if the circuits
saturated condensing temperature (SCT) drops below the specific
Fan Level Min Pressure (ConfigurationCOOLOFC
x.MNP). The number of fans and contactors on at a given fan
level depends on the specific unit options and size. See Tables 6
and 7 and below text for specific fan and contactor status at any
given fan level.
Units Without HumidiMiZert System
Outdoor Fan Motors (OFM) are controlled by Outdoor Fan
Contactors (OFC) which are controlled by the main base board
(MBB).
For 48/50PG0307 units, a duel speed motor is used. The
Compressor Contactor (C.A1) turns the OFM on in high speed and
the OFC1 is used to change to low speed.
For 48/50PG0814 units, OFM1 is controlled by OFC1 and
OFM2 is controlled by OFC2.
For 48/50PG16 units, OFM1 is controlled by OFC1 and OFM1
and 2 are controlled by OFC2.
For 48/50PG2028 and 48/50PM1628 units, OFM1 is controlled
by OFC1, OFM4 is controlled by OFC3, and OFC2 controls the
remaining two fans (16 and 20 size) or remaining 4 fans (24 and 28
sizes).
Units With HumidiMiZer System
Outdoor fan control for HumidiMiZer units includes a
Motormaster variablespeed control of some or all outdoor fans,
depending on unit size. The Motormaster control automatically
adjusts the outdoor fan speed to maintain approximately 80 to
100F condenser temperature for circuit A at all outdoor ambient
temperatures. Some unit sizes have additional on/off staging of
some outdoor fans. The fan level operation is determined by some
or all Outdoor Fan Control configurations described above, plus
additional HumidiMiZer Configuration (Configuration
HZMR). Refer to the HumidiMiZer operation section for
details on the Reheat function fan control.
48/50PG and PM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrier 48 50PG C03-14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrier 48 50PG C03-14 in the language / languages: English as an attachment in your email.

The manual is 9,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info